Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I am using the NRF52 development kit and I modified the uart example main.c to simple TX and RX application using printf function. The board is directly connected to the PC...
Good morning,
I ended up changing the design to use the nRF52810 chipset and I wanted to find out if Nordic would be able to provide some schematic feedback for my design...
Hi Nordic expert,
We are K5DET1/3/5/7/9/11 output high level, then string 10K resistor, K5DET2/4/6/8/10/12 through the mercury switch to read this high level, while adding...
Hi,
According to the documents of NCS, CoAP Server sample uses native OT CoAP API while CoAP Client sample uses Zephyr CoAP API, and the Zephyr CoAP API is recommanded....
I've googled all over, and I'm having a hard time finding any documentation that digs into how to use the nRF Connect SDK. Most documents point to examples, however the wealth...
Hi，
I developed with ncs 2.1 samples esb ptx and prx using nrf52840 make a low latency application，There are two problems
①On the ptx side, packets are sent twice in...
Hi, in our project we have to send some raw data to one node to other node using zigbee. So i have checked every single example but it doesnt match with what i need. I have...
Hi,
I'm trying to write a simple python application on Windows 7 that communicates with a BLE peripheral running Nordic UART Service. I'm using the nRF dongle and pyserial...
Hi,
I'm trying to config my SAM-M8Q with an array of HEX.
It's work beautifully with app_uart_put like the picture below.
However, when I try to implement LIBUARTE...
Hii
I have a problem pass the address while advertising
I should pass the adress using 9160_dk
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART...
Hi there, I'm trying to find a hardware integration guide that details min max specs for the IC and also details the RF output pin impedance so I can match to my board stackup...
I checked out the nrf github repo and tried to build the nrf_dm sample for the nRF 52840 dev kit which is what I have
In VSCode I chose "Add an existing application" and...
Hi,
As the title, I can see Mesh Proxy service in nRF connect app, after provisioined device by nrf Mesh app. But when I send data to Mesh Proxy Data In, It disconnect immediately...
I followed the document and downloaded nRF Connect for Desktop in Ubuntu 18.04.5.
Then I changed the permission of nrfconnect-3.11.1-x86_64.appimage to "allow executing...
Hi,
We have an issue that is puzzling us.
The symtoms are the following.
If we flash v1 of our application (using Segger Link) to our target, it works correctly, no...
