Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
I tried building and debugging the sample "https_client" using the method described here . But debugging fails. Debugging stops prematurely because the source file cannot...
I need to be accurate to five decimal places.
Use nrf52840 and ses.
Test code:
Execute d=atof(mm)/60.0 result 0.70693.It's right.
But e xecute d = 0.70693+22 result...
I am trying to use SAADC.
When viewing the contents of nrfx_saadc.c in SEGGER IDE all the code is greyed-out.
I verified it is enabled in sdk_config.h:
// <e> NRFX_SAADC_ENABLED...
Hi everyone,
I am currently attending the nRF Connect Fundamental Course.
As you can see from the picture below (taken from the Course material), there must be the chance...
Hello DevZone,
I was tinkering around with the speed of the TWIM0 module in the nRF52832.
I have a cheap USB logic analyzer to help me display the waveforms and I made...
Hi,
I am using NRF52832 development board , to which i have interfaced LIS3DSH accelerometer sensor(3.3V i2c)
when i configure it for 1600 sampling rate and all the...
Hello,
I am using nRF Connect for Desktop v3.12.0 with Programmer v3.0.4 on Mac. When I program mfw_nrf9160_1.3.2.zip on the nRF9160 dev kit, it works, but when I try on...
Hello! Very quick question. The available Zigbee and ZBOSS NRF documentation repeatedly to code examples that I am unable to find. The only examples I have are at nrf/samples...
I've previously successfully done interval advertisements using a SoftDevice with Nordic's previous (non-Zephyr) sdk, but I'm having issues replicating it on Zephyr.
Our...
Hi, I am using the nRF52840 with the softdevice s140 6.1.1 with the SDK 15.3 with FreeRTOS. Sometimes after collecting data for a around a day the device sometimes crashes...
Hi,
It has been a while since I looked up on different resources to get SPI slave transaction example and I finally found on the `nrf / samples / tfm / tfm_secure_peripheral...
Hello,
I have three questions regarding FEM.
#1 According to the following URL, FEM function is supported only for nRF52 series.
Would the FEM function be available...
Hi We are working on a new product that includes NFC, When we measure the voltage level we do not reach more than 600mv. The matching was done by capacitors: using a 2uH antenna...
Dear all,
I could happily flash my firmware to my nrf52840 upon pressing reset button. When pressing the reset button the diode on the board started to beat red and via...
