Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
I have a nRF52840-DK that stopped programing.
As a starting point to get it back to work, I reflashed the Interface MCU Firmware.
It is correctly detected by J-Link Configurator...
Hey Nordic,
My project is based on "ble_app_uart" and "ble_app_uart_c" examples. I modified them to some extent. You can download them from here .
Normally, I can write...
Hello!
On 3 and 7 of August my employee directed to you several questions regarding NRF. Case ID: 293339
Can I at least urgently receive the answer for the question in...
Hi,
We need to test our product for reliability when it comes to BLE connection in the vicinity of other BLE and WiFi devices. Do you have any suggestions on how to perform...
Hi all,
I am trying to use the bt_disable functionality on Adafruit Feather sense which has nrf52840 to restart a connectable BLE Service. The first call to bt_le_adv_start...
I'm developing an application using the NRF52840. I'm using the ADC, and there may be times where the signal to be measured is up to 1.8V, but the NRF52840 is not yet powered...
I am using the NRF52840-DK REV2 to program my custom board. I am using the debug out port and connecting it to my custom board, I tried both powering the custom board through...
Dear Nordic Engineers
I have a problem and would like to ask you about the I2C work state.
I read this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All,
I am working with NRF beacon project currently, and I explored many other NRF connect SDK sample projects like, Ble peripheral, ibeacon etc. But I am unable to...
Hi,
I'm trying to implement FreeRTOS on nRF52832 using the S132 SoftDevice and SDK version 17.1.0.
This is meant to read multiple sensors at a configured frequency ...
Hello all,
I have managed to connect the BLE module, based on the nrf52820 via the SW (4 pins) to the nrf52dk and surprisingly programming works via the Segger EM !
Indeed...
Hi,
I would like to carry the full modem update. Based on nordic website I need at least 4MBytes of flash for doing a full modem update on the nRF9160:
https://developer...
I have two Windows PC’s with an installation of SEGGER Embedded Studio on each and a nrf52832 project.
With the project and the library on a USB memory key running the debugger...
Hello,
I developed a driver for communicating with the kx134-1211 accelerometer over SPI for the nrf5340-dk. The driver works when the following pins are configured for...
