Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
we are developing a way to define through code a zigbee device composed of multiple endpoints, based on nRF5 SDK for Thread and Zigbee v4.1.0. The program can be flashed...
Hi all,
I'm trying to increase BLE throughput of ble_app_uart example (from official SDK16/ s132).
I've searched quite a few tutorials on which parameters should be...
Hi,
We need an detail description about uint32_t dev_config used in int i2c _configure ( const struct device * dev , uint32_t dev_config )
(zephyr i2c: https://docs...
Hello everyone.
I am beginner dev. I wanna run Serial Example Mesh and received data from BLE sensor. Can you support me complete this Project.
Thank you so much!
I'm testing a simple application based on the UDP/CoAP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi:
I want to use saadc peripheral,when i run the example "nRF5_SDK_17.0.2_d674dde\examples\peripheral\saadc",it worked well,but when I want to port this example to "nRF5_SDK_17...
https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/nrf_dm
I used the demo linked above to test RTT and DHCP respectively. Within two meters, I found that...
From the DF spec, we know that the connectionless AoA puts the CTE signal on the periodic synchronous adv, why, and what is the benefit. Is it possible to send CTE in extended...
Hi,
I am using nRF5340DK for development. Currently, I have two problems:
QS1: When I use fun nrfx_gpiote_out_toggle(), it reports Assert error on NRFX_ASSERT(! pin_in_use_by_te...
Hello,
I am working on integrating wireless-timer-synchronization into the HCI_RPMsg sample provided with nRF Connect SDK. My goal is to synchronize ADC sampling between...
Hi all,
I am using the kit nRF5340-DK, connecting to windows 11 pro. Already installed nRF Connect for Desktop 3.10.0 and nRF Command-Line Tool 10.15.4 (32/64 bit).
It...
Hi:
I want to include the Characteristic value in the advertising packet，for example the real time battery level，thus there is no need to establish a connection between...
Hello.
I wish to implement a DFU Client. One (USB connected) nRF52840 based device should update an other (Wireless) nRF52840 device.
As the SDK only has a DFU service...
