I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi there, after installing toolchain and SDK (2.9.0) on Windows 11 (python 3.10) I've successfully build an example and generated the merged.hex but issue occurs when trying...
Hi, one of my nRF52840 dongles cannot be detect in device manager. When I plugged it into a USB port on my pc, the red light slowly blinks and it didn't appeared in ports...
Updating from NCS2.6 to 2.8, the access to my QPSI Flash chip got broken (mx25r64, connected and configured using QPSI exactly as per the nrf5340DK board)
DTS entry:
...
Hello there,
I got an error msg when I tried to compile the Bluetooth LE UART service example for nRF54L15-DK as: " devicetree error: /chosen: undefined node label 'uart0...
Hello, I' needing some help on setting up the MCUBoot for the BL5340PA using the ncs 2.6.2. Currently I have the below add on for the prj.conf for the application core:
...
I am using the LORA Drivers provided by zephyr for testing my SX1762 lora module with NRF52833 Development Kit. I am able to initialize and configure the LORA Peripherals...
Hi,
I am working on an FCC cert of our product which is nRF52811 based. We are currently on SDK 2.0.0. I have copied from the nrf samples bluetooth area the projects peripheral_uart...
1.After I burn AP CODE, executing "nrfjprog -f nrf53 --program factory_data.hex –sectorerase" instruction will cause the following error. This issue wasn't happened in prior...
I am trying SPI Master/Slave communication between two nRF54L15-DK boards, using the nRF Connect SDK v2.8.0 and nRF54L15-DK 0.9.1 and 0.8.1. However, it seems that the SPIS...
Hi,
I just got my Thingy91x up and running, and it’s been on for a few hours now, but it has already used 460/500 location requests. How often does the unit send location...
Hi, I am trying to flash to a new design which uses ublox NORA-B120 module. I am trying to flash from vsc. But the flashing fails with following error.
Anyone can help...
Hello,
I have configured 2 nRF5340 boards for LE audio streaming from my mac. Two things I am noticing:
1. The audio is streaming but it is intermittent. Audio plays...
I found out nrf_reset_network_force_off() can be used to turn on/off the network core in firmware, per the example in NCS v2.5.0, samples/subsys/ipc/ipc_service/icmsg . I...
Hi,
I am making an application based on the peripheral-nus example. The checking for CR is removed and all characters are just sent further when available. The problem is...
