I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi All,
Now i'm using peripheral - blinky project,and i saw the Block allocator module in the sdk_config.h.
Can anyone tell me what is the Block allocator module use for...
Hi,
I met some problems when I tried the sample 'direction_finding_connectionless_rx' in ncs v1.7.1 on nRF5340dk. I copied files to hci_rpmsg/boards as https://developer...
Hi all,
I got my nrf5340PDK working with the Thread CLI Sample.
I can now connect to the UART interface and issue ot commands.
According to the tutorial Thread: CLI...
In response to a BLE_GAP_EVT_DATA_LENGTH_UPDATE_REQUEST, we have called sd_ble_gap_data_length_update, with the following parameters:
Rx Octets: 251/ Tx Octets: 251
Rx...
Hello everyone, i need to increment a counter each time my button on the nrf534DK is pressed i'm using sdk v 1.7.1 . is there a simple way to do it or a function which supports...
Hello!
I've seen similar posts about this issue: https://devzone.nordicsemi.com/f/nordic-q-a/57105/nrf9160-modem-stuck-in-searching https://devzone.nordicsemi.com/f/nordic...
I am looking to handle low priority interrupts on a single GPIOTE Port Event but when attempting to add the second pin with the same handler i get an error and the handler...
Hi Team Nordic and fellow engineers, I am seeking to find better parts from Nordic RF Transciever lineup
to replace nRF24L01P-R, in order to improve the performance of the...
Hello, I intend to use libuarte under FreeRTOS together with the SoftDevice (SDK 17.1.0). An app_timer is used for the RX timeout. I think there might be an incompatibility...
Hello,
I have a situation where I would like to reset the MCU (nRF52832) under Zephyr. For the most part I use ```sys_reboot(SYS_REBOOT_COLD)```. However, I would need...
Hi,
I just downloaded both versions 1.7.0 and 1.7.1. Compiling asset_tracker_v2 right out of the box with west build -b nrf9160dk_nrf9160_ns --pristine I get the hex files...
I built a game controller hardware for windows . I am supposed to have a few millisec. latency on notifications.
But the latency seems to be noticeable. I have also tried...
Hello everyone!
We've integrated the readout protection to our project, but unfortunately now we don't able to disable it.
The activation code presented below:
...
Hi
I would need to work on Master Branch. I have Toolchain Manager 0.10.1 and I have downloaded nRF Connect SDK 1.7.1.
I know that Toolchain Manger has not Master branch...
