I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Morning,
We have a technical question please. As far as we know the NB-IOT services in Germany should use only Band 20 for operation, but we see in our lab tests that some...
Hi
1、The customer wants to set read protection during batch programming，Customers use offline programming during mass production；
2、In addition to using nRFgo Studio to...
Hello.
I know that I can change the interval of the advertize event by changing the advertize interval, but I don't know how to set the interval to be sent to each channel...
Hi, We did design our own board/pcb using the nrf9160, but we have a problem to connect to network/lte. I did some debugging and I found out that when the method lte_lc_init_and_connect...
Can you please tell us what is the power consumption in Idle State with DRX = 1.28s and Sleep State with DRX = 1.28s? And an estimate with eDRX at 5.12 s? We are asking because...
Hello, I am using nRF52832 dev kit. I am trying to get lower current consumption. I used ble_app_blinky example and disabled the NRF_LOG. My settings are below:
Role: Advertising...
Hi, I used my NRF52840-DK for few times but suddenly the jlink connection was not detectable. Before the Jlink failed, the main controller on board did not bring up the board...
Hello,
I Cant upload BLE Code on nRF52832 breakout board from nrf52 Dk using Segger studio. Other codes such as blink are uploaded successfully. But there is problem for...
Hi,
I am trying to use radio notifications (mpsl_radio_notification.h) to call notify with data just before central connects. I do this with no problem with NRF52840.
...
Hi everyone. I just bought the nrf52832 Develop Kit. However, after trying to flash write the sample, my nrf52832 Develop Kit doesn't work and won't flash write the next time...
Hi, I'm using BC805M module which uses nRF52805 SoC.
I have a power ON/OFF button on the PCB. If I press the button (deep sleep mode) during BLE connection, the BLE will...
Hi, I'm using nRF52805.
In my code, I used BLE to transmit I2C and ADC data to the mobile app nRF Connect correctly and continuously.
I tried to use NRF_LOG_INFO() and...
Hi. I am working on firmware for nRF9160 based IoT device Already found a way how I can switch between two different images in flash from the current firmware and it's super...
