Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Repetition of the steps followed here.
(1) Generated priv key, and public_key.c file using nrfutil, (2) generated the bootloader_settings file using nrfutil (3) Compiled...
hi!
nordic team
i am using thingy 52,and i meet a question that app_thingy_s132.axf: Error: L6405E: No .ANY selector matches accel_auto_cal.o(.bss) when i compile this...
Hello,
I am using nrf51822 with sdk11.0.0.
i observe that in while loop sd_app_evt_wait() function take much time for next interrupt to be pick.
is there any alternate...
I am developing a BLE anti-lost APP with community search, I set scan continuously or scan window 5 secs and scan interval 10 secs, but it drain phone's battery. How long...
Hi there,
I am working on having serial bootloader in nrf51422 to perform dfu over UART. DFU serial bootlaoder example in sdk11 claims to do the same.
After flashing...
I can't figure out why I can't send ADC values to the NUS service via BLE correctly. I should be getting hex values that convert to something like 0 or -1, since the ADC pin...
Hi all,
I'm currently learning on how to build bluetooth connections with a device from an app. For that I downloaded the iOS version of the nerf Toolbox app, as my chip...
hi
I am using nRF52 DK
Loaded Blinky Peripheral
I Connected this nRF DK to Com Port and Started Master Control Panel
But the Start Discovery Button is Disable. Please...
Hi,
I have an issue wherein once OTA update is complete through nRFToolbox (Toolbox says " Upload Complete") the Device does not reset and shows that it is connected to...
I am in the development stages of developing a ble application with the nrf52840 nordic chip.
I have come to realize the increasing difficulty of debugging this chip only...
Hello,
I made a custom board based on nRf52832, and I am using SDK 14.2
When I use a slightly modified version of the ble_app_uart example, I see it with nRf Toolbox,...
Hello,
I'm trying to configure 2 serial ports for a custom board with nRF52840 chip, but when I try to instance the second UART "NRF_SERIAL_UART_DEF(serial_uart1, 1);" the...
Hello,
I have an nRF52840 Preview DK, I would like to try the advertising extensions you introduced in the new released SDK.
My Goal is to make an application which send...
We're using a combination of the ESB library/example code and the USB CDC ADM example code to transfer data from one 52840 dev kit to another system via a 2nd 52840 dev kit...
