Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi
I have an external NOR flash chip which is powered off on startup. The idea is to power up the flash when needed to reserve power. On startup, I get the error message...
I haven't found much documentation yet regarding multiple threads in the secure partition, so I wanted to ask if this would be possible. Was planning to also test it out myself...
Hi,
We have a requirement to not exceed 63 mW of WiFi Tx power at any time for any band (2.4 or 5 GHz) . There is a statement about changing Tx power is not supported. Can...
Hi, We are currently migrating our project, originally developed with NCS version 1.8.0, to the latest NCS 2.7.0, while incorporating MCUboot for both of them. During this...
Hello,
I am encountering an issue with the nrfutil settings generate command. Each time the command is executed with the exact same parameters, the resulting settings.hex...
SoC: nrf52840
SDK: OpenConnect 2.4.4
I have been developing an ambient noise system using I2C microphone, nrf52840 and Zigbee networks for some time. The firmare reads...
Hi,
Is nRF52811 / S140 capable of simultaneously being in peripheral (connected slave) and central (connected master) mode like described in this blog post https://jimmywongiot...
I’m working with the nRF5340 and nNF Connect SDK 2.6.1. I’m encountering an issue where, after a central device (e.g. an Android phone) forgets a bonded peripheral device...
There was a previous discussion about the option to disable/enable slave latency a few years ago:
Did this ever get implemented? Specifically interested in the feature when...
SDK: 2.6.1
I needed to add a single wire support to our device recently and I did that by using two pins TX/RX shorted and UART. It works, but current consumption sky rockets...
Hi all
How would I be able to generate and view the calculated hash that i get while using the dfu library? Is there an easy way. I'm hoping to generate one single hash...
I am looking for the code example of how to setup A-GPS/A-GNSS on a nrf9160 dk, but I am not able to find one. I am only able to find these links:
https://developer.nordicsemi...
Hi everyone, I'm encountering an issue with MCUboot on NCS 2.7.0 and my custom board based on the nRF52840. The bootloader was functioning correctly with NCS 2.4.0, but now...
Hello,
I'm using nor flash with qspi as an external storage.
I'm facing problem where i can have different NOR Flash chips (with different jedec-id). Is there a way to...
I am testing ble_app_hid_keybpard of SDK17.1.0 using nRF52-DK board. After running, if BLE connection is not made, it enters Sleep_Mode after slow advertise. At this time...
