Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
i have used this case:devzone.nordicsemi.com/.../using-swo-with-nrf52-redux and add ENABLE_SWO but when i flash and use jlink swo viewer,it will have this problem.
...
Hello DevZone!
I am using a nrf5340 with the nrf Connect SDK v2.6.0. I have been running into an issue that has come up a few times on separate occasions. Basically, for...
Hi,
i develop my product ny ncs V2.6.0. when i view the code
I noticed the annotation, it says “Edge interrupt gives only 7 channels. It is not suitable for larger matrix...
Hi. I have some question regarding to Bluetooth 5.4 on Nordic platform
1. Can Nordic platform do Advertising Coding Selection? I saw some old old issue that the device...
Hi,
I have tried to update the nRF Connect for Desktop app (v.4.2.0 to v.5.0.2). Unfortunately, the process does not work through the end. Once the installation of the new...
I have to use 240 bytes for my sensor value to send in bluetooth. so i choosed to work on ble_app_att_mtu_throughput i need only pheripheral to work on it . i have to remove...
Hi, I was wondering if hosting more than one nrf Connect for desktop version on the same computer was possible. The reason is that I need to use both the old app LTE link...
Hello,
I have connected a LSM6DSO sensor to my nRF52805 which is powered via GPIO. At startup zephyr RTOS wants to init the sensor and failed. After a reboot it detects...
On the SDK 17.0 NRF52840 platform, using sd_temp_get to read the chip temperature works correctly. However, if the sd_clock_hfclk_request function is used in subsequent operations...
Hello,
I'm trying out the example code "pin_change_int_pca10056". But the delay time between sensing a voltage change and toggling the output GPIO is quite long. 22us. Is...
I wanted to know in what ways can I connect thingy:53 to nrf9160 dk via Bluetooth? I understand that dk has onboard nrf52 and hence thingy:52 could get connected wirelessly...
Hi all, I am using the nRF52840 and I came across the nrf52_handle_approtect() func in modules/hal/noridc/nrfx/mdk/system_nrf52.c.
In the nrf52_configuration_249() function...
Hi,
I am unable to access P0.09 and P0.10. I face a similar problem to this thread . I've declared CONFIG_NFCT_PINS_AS_GPIOS=y in prj.conf. Also I've checked 0x1000120C...
i have a custom board that uses a nrf5340 that has been hardware modified so i can work again on getting my board to draw the mimimum power from the battery.
i have a PPK2...
