Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hi, I'm working on a custom board with the nRF54L15 using NCS 3.2.1, and have configured spi21 on port 2 for a display. SPI pin configuration: SCK: P2.06 (TRACECLK) CS: P2...
I am working my way through the DevAcadmy (nRF Connect SDK Fundamentals) using an nRF52840 development kit.
In lesson 6, exercise 1, I try to get an I2C with a BME280 to...
In sdk-zephyr/samples/boards/nordic/battery/src/battery.c at main · nrfconnect/sdk-zephyr
nRF54L series doesn't have 'SAADC_CH_PSELP_PSELP_AnalogInput0', how should it be...
I am trying to interface an SD card over SPI on nRF54L15 using nRF Connect SDK .
I started from Nordic’s fs_sample , which by default uses SPIM20 on Port 1 pins , and this...
I am using SEGGER Embedded Studio v8.26 with J-Link software v8.94 on Windows (64-bit) for BLE development on the nRF52840 DK .
Using J-Link Commander , I am able to:
...
After upgrading my NCS version from 3.1.1 to 3.2.0 for the nRF54L15, I found that the GRTC resets after a sys_reboot(), whereas it didn't in the previous version. What changes...
Hello everyone. I'm using the nRF52840 Pro Micro board with the J-Link programmer and the nRF Connect extension for VS Code. This board comes with a U2F bootloader, but I...
I use a hardware timer to capture/compare incoming pulses using PPI to trigger the captures from GPIOTE. I previously wrote the same application for nRF52832 on the old SDK...
When running SLM on nrf91, it sends "Ready\r\n" over UART on boot/reset. On nrf54, we use "Ready" to detect reboots and rerun the setup. However, when the modem reboots, sometimes...
Hello Team,
I am using the nrf54l15 custom board for development. I have configured the P1.06 as a normal GPIO as follows:
And using it as follows:
The pin status...
I use example from nrf52 SDK. project path:nRF5 SDK\nRF5_SDK17.1\examples\ble_peripheral\ble_app_uart\pca10040e\s112\arm5_no_packs.
emulator: ST link V2
but no target...
Hello,
The nRF5340 supports audio transmission, while the nRF54L15 supports Channel Sounding. Is it possible to conduct audio transmission simultaneously with Channel Sounding...
We need to use a Lithium Ion battery to power our device and need to connect to a chip that has 1V8 logic levels as its only option.
We're early in development, so it seems...
I am encountering a strange hardware/software mapping issue with the SAADC on an nRF52833 DK running on Zephyr (NCS) . Using VS Code nRF Toolchain and SDK (V3.2)
The issue...
This one gets complicated as I cannot reproduce the problem with my original NRF5340 DK.
Steps to reproduce are trivially easy, but only fail when using my favourite OEM...
