Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Dear Nordic,
we are developing FW based on nRF52832, SDK 17.0.2. We have 2 devices: BLE Central with SD S332 and BLE Peripheral with SD S112. The Peripheral is basically...
Hi, I am working on an IoT project that will use lwm2m, I developed an event manager architecture using the helloworld example base. Now that I am starting to develop the...
Hi,
Is it possible to check somehow if a BLE packet has been transferred (or not) from a peripheral to the central device?
Through a succesful transmission flag or something...
Hi, I'm using nrf52832 custom board and 14.2 SDK, S132.
In my program I'm using SAADC, PWM, I2C along with softdevice and PID. my device is working fine for some time but...
Hi! I've noticed that softdevice S113 is Bluetooth 5.1 compliant , and that the nrf52 family chips are Bluetooth 5.2 compatible in terms of hardware. a. Is there any target...
fds_init fails for several valid reasons, but my issue is how to recover. This for me was triggered by a firmware upgrade overwriting the fds file area. This can trigger fds_init...
Hi, I learned how to replace the softdevice for a normal application. I've replaced 140 with 340 in my app. However I don't know to do that for the boolloader.
What I want...
Hi Nordic,
I want to control an LED with the nrf GPIO, the LED Anode is connected to VDD, through a resistor, and the cathode is connected to the GPIO. Under this configuration...
I want to use the nPM1100 to battery manage, and supply power to the nRF52xxx - along with a heavy duty load ***directly across the battery***, so that full battery voltage...
Hi,
I'm running the experimental example: 'ble_nfc_pairing_reference_pca10400_s132' using sdk17.0.2 (and 17.1.0).
After I installed the micro-ecc following the guide on...
Hello
I am evaluating design of wireless communication in power supply with nRF24L01P , and I have 4 questions.
1.I want to know the Mean Time Between Fails (MTBF) and...
I'm using softdevice s140.
My power comes from a CR2032 coin cell.
My board has a 1.8V LDO (Toshiba TCR3UM) because my temperature sensor is calibrated for 1.8V (TMP112B...
Hi,
Looking at the source code for nRF Connect SDK v1.7.0-677-ge3c356ec8 and SDK For Mesh 5.0.0 I can't find any indication that the following section of the Mesh Profile...
Dear Nordic,
we are devepoling FW based on nRF52832, SDK 17.0.2. We have 2 devices:
BLE Central with SD S332
BLE Peripheral with SD S112
We setted up an open BLE communication...
