Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I have an NRF9160 system running and I see mention of " The nRF9160 PWM peripheral can capture the period and pulse width of an external PWM signal" but was a little confused...
DeviceTree Visual Editor shows SPI1 as enabled, but the changes are not reflected properly in the GUI or in build behavior.
I receive the following build error : " DT_N_S_soc_S_gpio_50000000...
The nPM2100 datasheet (v1.0) provides Figure 8: Load current triggering mode change vs. VOUT.
Can you confirm:
1. Consider the system is in Low Power mode. If the load...
Hello,
I am trying to implement OTA through BLE, and as Im building the program, Im getting a build error as :
error: 'FLASH_DEVICE_BASE' undeclared (first use in this...
Hello. I have a light sensor connected to 2 gpio pins on nrf5340, Enable Pin : P0.08 and Output Pin: P0.07 Trying to trigger an interrupt based on the light. With the button...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
Hi,the Nordic team I'm working on low-power devices that Matter over threads by nrf54l15,I found a problem at present. I interrupted the configuration of the two PIR input...
Hi all,
I’m working on an nRF5340 project where the network core runs a hci_ipc firmware to forward HCI RAW packets to the application core, which then parses vendor-specific...
Hello DevZone!
All samples with Application Event Manager (CAF, nRF Desktop) has simple main function like that:
Main thread has terminated after executing and main...
Dear reader,
I am currently working on a project involving the NRF54L15 microcontroller. In the specifications of the MCU, under Circuit Configuration 1 for QFN48 (QFAA...
Hi I’m looking for some advice on what may be drawing power from the thingy 91x.
I have measured the power consumption of the nrf91 the nRF 5340 and the nRF 7002 using the...
I want to use P0.13 for ADC reading. However, I noticed that it is already used as an SCK pin in this configuration:
spi3_default: spi3_default { group1 { psels = <NRF_PSEL...
Hi!
I’m currently setting up multi-image DFU on the nRF5340 using external flash.
By following the official documentation and samples, I managed to get it working correctly...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
I'm getting timeout errors when trying to program a Thingy:91 with a J-Link Pro PoE on macOS on an ARM Apple M3 Max.
Here's the command and error message:
I get the...
