I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi ,
I have question about the specification of CPU running current. We did measure the current by PPK to force the CPU always running but the result is quite different...
Dear DevZone, I'm trying to perform a BLE OTA DFU with two nRF52840 Dev Kits. I followed the step by step guide from Nordic provided at the following link: devzone.nordicsemi...
Hi , Dear Nordic supports:
I am using NRF52832 for the iterative development of a product. In the previous generation of products, I used a PWM control LED flashing, whose...
Hello.
Could someone recommend me a verified antenna RF Switch for AoA using Bluetooth nrf52811 ?
What parameters are crucial for proper functionality with nrf52811? ...
Hi,
In ble_app_cts_c example(SDK 16), is it necessary to perform app_timer_init()? Because I could see that, no timers are being setup in the function timers_init().
If...
Hi,
When I read about interframe spacing in the product spec ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fradio.html&cp=4_0_0_5_19_8&anchor=ifs ...
I have a nrf52832 chip acting as a serial passthrough to an external app. Basically, it works great, unless I start sending high amounts of data into it. Once I do that, I...
I am developing an IoT system in which I need to link multiple devices to a master, which is why my nRF52810 chip caught my attention so I am interested in knowing how many...
The address range for Bootloader is from 0x0007 8000 - 0x0007 E000 for SDK 16 on nRF52832 device. See this link ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16...
Dear Sir,
Using SDK 16.0 for NRF52833. My application uses NRF FDS lib (flash data storage)
Immediate fds read after fds write gives 0. But after a board reset I get...
Hi,
I am using nRF52840 S140 with ble_app_blinky application. I have a basic query of GPIO configuration when moving from Bootloader to Application.
We are using Secure...
I'm using ble_uart_app and wanna Low Power Current Consumption but its consuming 330uA. disabled the nrf_log form sdkconfig file. main code is below. Please let me know what...
Hi,
When nRF9160 is used as a co-processor and an external host MCU is used to interface with nRF9160, what are the serial interfaces that are allowed? The at_client example...
Is it a better choice to use the NCS for nRF52840 development, given that it is the new platform going forward? Am I painting myself into a corner developing with nRF5 SDK...