Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi sir,
I am using ble_app_uart to send the enegry value to the mobile. for energy calculation i am using internal rtc oscillator but after 179 secs the device stops working...
For example, I get logs like this, and I want to know what these events are:
ble_cts_c: BLE event handler called with event 0x57
I also see 0x36, 0x12, etc. when the CTS...
To the kind attention of Nordic support team,
after doing some ble bonding between an nRF52 device and an host computer, I can see this situation in device flash. So, these...
Hello,
I am trying to develop a sensor which can connect to multiple sensors and send the data which is received by its UART through bluetooth, at the peripheral. Central...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
when i copied the spi_fujitsu_fram example to my project folder on c drive, i am getting this error "zephyr/linker.cmd:70 cannot move location counter backwards (from 0000c23c...
Hello!
I would like to know if there is any way to route the signal from the main LED from Nordic Thingy 52. I checked its data sheet and I only found the pinout for other...
After downloading nRF5 SDK v17.0.2, I checked the Release Notes - and they state SES v4.50 has "been used for testing".
So I downloaded & installed SES v4.50
The HID Keyboard...
Hi, recently I want to establish a connection between two development boards (STM32F103 + nRF52840-DK), that the STM32f103 board can create the data and send it to the nRF52840...
Hello, I have a project running on a PCA10040 board, using softdevice 132 (0x9D, v5.0), ble and serial port for data transfer.
I want to migrate this project from this...
I am trying to use the UART for a custom version of the DFU. I have it transmitting no problem, but I never get the RX_DONE event. I cannot see any reason and I have looked...
Hello,
I have a question because there is a problem with writing code using timer.
I wrote the following code to avoid using the LED timer when I first ran it.
However...
Hello Please help. I want to connect ble central to a specific address. And the ble peripheral has a ble central address, that can connect to it. 1. Is a whitelist used on...
hi,all
i am a new learner about the BLE
when i use softdevice 17.0.2 to run the example (anyone) ,there is no problem.
then I want to use the SDK12.3.0 to run a formal...
