I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hi
I'm using the Eval Kit PCA 10001 V2.1.0 and Nexus 5 with new Android version 4.4.2. Connecting to the Eval Kit works just fine, but when i perform a service discovery...
I have an nRF51822-based peripheral using the SoftDevice 110 v7.0.0 and SDK v6.0.0. The peripheral uses two custom characteristics under a single custom service. I'm using...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode.
For some reason it comes back immediately, but I can't figure out why.
If I call it a second time it stays...
Hi,
I'm trying to flash the S110 onto my nrf51822 SoC, but nRFgo gives me the following error. (Also, hitting recover just gives me an error: "an error condition was detected...
Within app_button module, code for app_button_is_pushed() seems to have changed from SDK version 5.1 to 6.0. I notice my code has stopped working properly with that update...
Hi
Now, we are planning to implement an ANT+ RX (slave). I checked nRF51422 product spec. Radio current consumption is 12~13mA if receiving data between 250kbps and 2Mbps...
I'm using the boot loader that comes with the beacon development kit and I want to change it so that when the application software is running it can restart the device in...
I have managed to get the SPIS block working using standard sets of read and transmit buffers. This all works.
I am now trying to use the ORC register to send a single...
I am wondering how you put the nrf51822 chip to sleep. I've determined that the way to do this with the soft device is sd_app_event_wait() in the while loop. What about non...
Hello
I've been trying to create a simple BLE observer that outputs the nearby devices data onto the serial port using a PCA10001 board.
For this, I'm adapting the code...
Hi - I'm using the 51422 dfu bootloader from the nrf 6.0.0 SDK and it works fine with the iOS apps, I can send both .bin and .hex files to the device and it works fine. However...
Hi,
I am using nRF51822 evaluation kit. I want to develop GPIO isr (GPIOTE_IRQHandler) which can handle multiple GPIO interrupts. I have tried to enable the GPIOTE_IRQHandler...
Hi!
When using bootloader, I cannot update application data from Keil (for example for debuging), because after restarting bootloader is loaded and
!bootloader_app_is_valid...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
EDIT:
I'm using nRF51422-QFAA E00 and S310 v1.0.0, SDK - nRF51 5.2.0.
I'm starting HFCLK from externall crystal for ADC conversion. Since I have no SD enabled everything...
