Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
I´m working on a project to send measurement data over ble and receive it. This worked for me, but I want to send the message in my own struct.
What I found in the...
I am trying to use blesniffer on wireshark. I have 2 nRF52840 dongles.
I have successfully captured traces using the 802.15.4 firmware on Wireshark with the dongle appearing...
Hello, I want to know if a typical 50ma Maximum DC-DC converter ic is up to the job of powering up the nrf52840 device working under the heaviest load?
I can't seem to...
Hi Devzone
currently i am doing some test on example central_and_peripheral_hr.
in the orignal example central_and_peripheral_hr is using the BT_SCAN_TYPE_SCAN_PASSIVE...
Hi,
I have a simple question: how to get the link key of nrf5340 audio dk when streaming as gate and handset; we want to catch the airtrace.
BR
Zhongsan
Hello,
I used the NRF52810 controller for BLE application. I have a code in which BLE advertising packet length is 32 byte i have to reduce it to 23 bytes
Following is...
I am a user developing using nrf52832. I have a question about TX POWER. TX POWER can be set to -40, -20, -16, -12, -8, -4, 0, 3, 4 by using sd_ble_gap_tx_power_set(). I tried...
Hi All,
I am using nRF52805 in my application development(), everything working fine and power management is initialized using "power_management_init();" function. But i...
Hi,
My product uses two sensors, and S113 on nrf52833
I need to communicate and compute data before to update my ble caracteristic.
Sensor 1 takes 45ms to do this tasks...
Hello,
I am currently in the process of integrating the hx711 library written by one of your developers in order to sample weight data from a load cell and send it to a...
Hi, I am new to HTTP, and are trying to make a simple http post (not https) code for thingy91 over LTE. I have a http server that require some headers in the request. I have...
Hi
Tried to do something seemingly simple but failed miserably
I have some working code using SDK 17.0.2 (yes I know its old but its not going to be updated)
All...
Hi,
In the SDK 15.0.0, there is not libuarte sample under peripheral folder, my customer use SDK 15.0.0 to maintain their product.
Is it OK to migrate libuarte(from sdk17...
Hi All,
My application uses as provided below,
MCU : nRF52805 SDK : nRF5 SDK 17.1.0 SoftDevice :S112 v7.2.0 IDE : Segger Embedded Studio.
and GPIO(BSP),Advertising Modules...
I want to use the external flash memory MX25R6435F to run my code which has a big size on my arduino nano 33 ble but I'am a newbie and I don't find supports that can help...
