Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I am designing an application using the nPM1100 and I would like to know if I can use the VSYS as a power supply pin for my other circuit.
Is VSYS supplied by the battery...
In the nrf_sniffer_ble.sh script, the block that checks for an active virtual environment uses the following line:
if [ ! -z " $VIRTUAL_ENV "];
Notice that...
Previously, I compiled and downloaded the radio_test example into two DK boards.
I then used the CLI to set the parameters for each board one as TX one as RX
On setting...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
We are using the nrf52840-based module in our product.
This module is already certified with BT SIG.
Do we still need to certify our product with BT SIG certification...
Hi, As I am working on nRF5340dk and I am facing issues with flash memory. My application is exceeding the size of flash in nrf5340 (1MB flash). I want to move to nrf54 series...
This is a continuation of my previous thread ( Connections drop and don't come back (and "SoftDevice Controller ASSERT: 53, 296") ) (Case ID: 341823).
The project is a star...
Hello,
I am using Zephyr Toolchain v2.9.0 on an nRF9161 custom board . I have updated the modem firmware to mfw-nr+_nrf91x1_1.0.2 and flashed the board with the hello_dect...
Hi to you all. I have a question about how I can apply this mechanism in nRF52.
In modern TWS, it works like the phone or PC connects earbuds separately and sends and receives...
Hello, i'm having a problem with the satellite detection time when I start gnss search. When I start the search, for a while at first the satellites are not detected and then...
We are making a board with nrf9161 and nrf54L15 so that we have the GPS tracking facility and BLE . We wish to connect (send) other devices' data to this device (like temperature...
Hello,
I am testing the "peripheral_hids_keyboard" sample from the Nordic Connect SDK v2.9.0 using the corresponding toolchain version. When connecting the device to an...
After I added the device on the Samsung platform, I shared the QR code, and then added it with Apple, but the device could not be found.The log prompt is as follows:
For a project running a BLE connection and sharing data via the NUS service, we have seen that setting up Coded PHY (S2 or S8) will eventually produce an assert error as follows...
How to change Device Information in nRF Cloud? Where do I find the code setting this info? Where is "App Name" and "App Version" defined?
The application is nrf_cloud_multi_service...
