Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello,
This is my first experience with any nRF hardware and programming using BLE. I want to program my nRF52 development kit over the air from my windows computer via...
Hi,
I tried to use BLE DFU with nrfutil on my nrf52832 custom boards, but always get the result of 'Failed to open. Error code: 13', so I am trying to build the connectivity...
Hi,
I am trying to run the NRFX_SPIM example project code on my DK. But my DK is 10040/nrf52382 and the example project given in SDK15.2 only has a folder for 10056. Should...
Good morning
I'm new to these SoC systems, but I've developed a custom board with the nRF52810QCAA chip and I'm using the example (ble_app_eddystone) of the SDK15.2. softdevice...
Hello
I am now using nrf52832 and BLE communication with an Android terminal.
BLE communication is a beginner.
I am using nRF_SDK_15.0.0_a53641.
Since I programmed...
It seems possible, but I can't quite figure out how to use nrf_ble_scan_filter_set to use more than one device name. Any assistance? Alternatively, is it possible to use wildcards...
Hi,
In GATT level, on the receiving side - Is it possible to receive a corrupted packet or does the LL identify and discards such packets?
Specifically
- Will host...
Hi
I segger project get compiled and download successfully but it didn't start work. After put it in debug mode, it start working even after removed it from debug mode working...
I am working on a custom board with two MCUs, one nRF52840 and one older MCU.
In the previous iteration of this PCB the old MCU was connected to USB through an FTDI FT232...
Hi,
I've developed a relay application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently...
Hi
My application with SDK11 S132 softdevice is having some unknown issues that will make wdt or hard fault handler happen. And I am trying to use the following code to...
Hello I am using eddystone-beacon example from sdk 12.3 but i am unable to get notification on android phone,nearby setting is also enabled ,please help??
Hello,
I’m looking for an example using the Segger IDE that would read the SAADC and transmit via BLE.
The following example seemed like a good starting place:
...
I am currently working with an nRF51822, SDK 10 (can't be changed), s110. I have a nRf51822-DK (aka pca10028) and wanted to try the d fu_dual_bank_ble_s110_pca10028 example...
I use the nrf_drv_pwm to generate a pwm sequence,
The sequence works fine, but between sequences and at the end I am unable to control the pin.
It is always high unless...
