before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi all , I using timer 0 to count from 0 to max value 32bit . In my code :
If I using NRF_TIMER0->TASKS_CAPTURE[1] = 1; for save counter value to CC register . It run...
Hi Everyone
I am working on nrf52832 with sdk 14.0.0 on iar IDE. TWI and SPI separately working fine in buttonless_dfu then i merged SPI and TWI in buttonless_dfu itself...
I am trying to update an older application use the spi_5W_master and receive the error: (SDK11, using S210 softdevice)
:RTE\nRF_Drivers\nRF51422_xxAC\spi_5W_master.c(346...
Hi,
I'm trying to advertise 2 packets simultaneously, connectable packet using the soft device and a becon packet using the timeslot. I'm using nrf52 SDK 14.0.0 and SD132...
Hi I am doing some research for my paper, but It is my first time to use NORDIC board.
With broadcom and bluez combination, I could check data packet in l2cap layer, but...
Hi All,
I have a question about NRF52840 power consumption. It is not very clear from the datasheet what is the power consumption if I'd like to use only one of the DC...
Hi everyone,
Preface: I'm an educator and my students are familiar with the Arduino IDE, so I'm using that in combination with the sandeepmistry/arduino-nRF5 core.
Our...
Hi
I am developing nRF52832 wake up solution using LF (Low Frequency).
Initially, I develope it without sd_app_evt_wait .
After that, I am used sd_app_evt_wait to reduce...
Hi, I'm writing this because of nRF52840 booting error
I got this product today and It worked well, but after I downloaded one of the example's ~DEBUG.jlink file to the...
I may have a massive misunderstanding here....
Using nRF52, SDK 14.2, Ant S212.
I use a background scan to discover devices on channel 0, with a beacon on channel 1. ...
My isp (Internet Service Provider) doesn't provide ipv6. Now how do I send ipv6 packets (BLE over ipv6 packets).
Updated: I have an Nrf 52832 and I want to send access my...
Hi at All,
I’m currently working at a design using nRF52840. It’s extremely space sensitive and actually I’m not able to place all the needed parts to the PCB.
Therefore...
Hello
I want to get the MAC address of my custom device, is it possible to get the mac address of the nrf52832? and if it s possible , in which register? Thank you
ble_app_template.zip I need to setup whitelist. To achieve that while calling ble_advertising_init I specified
ble_adv_whitelist_enabled = true
then, while handling...
