I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
When implementing Shell NUS option we've faced with the following: NUS transport takes in account only 'enter' symbols and doesn't react to ones like up-arrow, down-arrow...
The interface "sd_ble_gap_adv_start" uses "adv" to indicate broadcast, but the interface "ble_advertising_start" uses "advertising" to indicate broadcast. Why not use the...
Hello Nordic Team,
I am trying to flash the existing BLE light example code to my BL653 kit with Segger Embedded Studio. After falshing the code into the board it is taking...
Been having trouble integrating systemview for tracing FreeRTOS application. I came across this thread , and even tried replacing the files with what's inside the PatchedFiles...
Nrf Mesh App Version 3.1.6
After provisioning 2 nodes, I connect to one as a proxy, whenever I try to "get TTL", "Read State", or refresh the configuration server after...
opened nRF connect and attempted to open the dongle with this. When I plug the dongle in without holding the button, i get this error
2021-02-14T20:18:30.648Z INFO Using...
I am unable to generate setting using nrfutil.
Command used is as follow:
nrfutil settings generate --family NRF52840 --application pca10056/blank/armgcc/_build/nrf52840_xxaa...
Hi
I'm trying to use the LIBUARTE library together with BLE_NUS example in SDK 17.2.
From the libuarte sample I add these lines to NUS example:
I also modify sdk_setup...
Hi!
I am trying to flash some Zigbee related code to experiment with creating DIY smart devices (specifically Zigbee and matter ones) using my Arduino nano 33 BLE. One problem...
Hi,
I flashed open_bootloader and it seams to work. I was following this question . However, after building application (I am using ble_central/ble_app_gatts example), creating...
hi,
im using nrf52811 customised board,for long range purpose im using softdevice s140
so i need to port secure boot loader pca10056 to pca10056e
can you please me reagarding...
Hi,
I have tested the ble_nus code in NCS v1.4.2
where i can't send 250 bytes
I want to send 250 bytes to ble nus data send for 100 ms once
How to enable data send...
Hello,
I use the nrf5340 pdk. I would like to flash the led1 with a duty cycle which is different from 50%, so i tried to open the binky_pwm project, but the segger shows...
Hello,
what is the correspondence between the number of pins indicated in the dts file with the port number and bit of the chip.
for instance:
& spi1 {
compatible...
