Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi,
My nRF52840 DK has suddenly stopped working. I have tried different USB cables but it's not turning ON when I connect the cable to the J 2 USB connector.
Observation...
Hello
In our application we're using the download client. Here are the cipher suites the modem supports in hardware: https://www.nordicsemi.com/Products/Low-power-cellular...
nRF52840, SD140, SDK 17.0.2
We're using UARTE to communicate with a peer MCU. We're using hardware flow control (CTS and RTS are enabled) and the baudrate is 115200. The...
Hello,
I'm using two nRF5340 MCUs with BLE5.2 audio in an application. I had a couple questions I hoped the Devzone could help answer.
1. On one of the MCUs, I was originally...
sorry for the perhaps stupid question - but despite several hours of intensive searching, I am not getting any further with the start -up of my new and beautiful Thingy91...
I do not understand how to compose these settings.
Using ncs v1.5.0 GPS sample with SUPL enabled.
This works OK on nrf9160-DK using the supplied settings
#define AT_MAGPIO...
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/61935/bootloader-flashing-error---nordic-nrf52840-usb-dongle I get the following error:
DFU failed: Error message...
Hi,
I’m trying to measure the current on NRF52840, SDK 17.0.2.
I have modified the HeartRate Measurement example’s advertising parameters as PLper my requirement.
...
Hi,
I am trying Zephyr for 52840 dongle. I am able to west build, but could not west flash.
While I do west flash, I get
-- west flash: rebuilding ninja: no work...
I bet you get sick of this, but I've looked at the other solutions and followed any advice, but no joy.
I am trying to use a Makerdiary nRF82540-MDK usb dongle to evaluate...
Dears,
When Reset pin(0.18) is used for QSPI (GPIO macro is not defined as RESET), after initialization ,Jlink is disconnect.
Would you please suggest it? Thanks.
I am using a nRF52840 dongle and want to filter ADC raw data. I have downloaded the CMSIS 5 DSP package.
And tried to include a copy of an example (arm_fft_bin_example_f32...
I found that AGPS can get location information via mobile network. With this feature "GPS" can work indoor.
1. Thingy91 also uses AGPS, but when I ran prebuilt hex asset...
Hey all,
I'm trying to install the nRF Asset tracker. I'm stuck at a step called Building the project using GitHub. I just need to know how to build the project using...
Hi,
I was trying to retrieve the log information from the Nordic to the AWS server. I can see all the log info with the Status as Error. I'm retrieving the logs from...
