Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Dear Nordic Support Team,
I want to integrate ble_app_uart_c and ble_app_multilink_central into a nRF52840 as an edge gateway, and the nRF52840 node communicates to the...
I try flash read, write and erase with flash_fstorage_example sdk 15 on nrf52 dk
On main.c i can write and read with nrf_fstorage functions.
When i try nrf_fstorage_erase...
I try to use SDK15/FreeRTOS project.
I measured current comsumption on IDLE state(not run any task).
It's take about 200uA.
On FreeRTOS's portable/CMSIS/nrf52/port_cmsis_systick...
Hello there,
I purchased some NRF52832 Development Kits and some NRF52832 Standalones. I wrote some code and flashed it to the development kit and it worked. Otherwise,...
Hi all!
I'm using the fanstel board. I can see that the "ble - uart" examples run ok.
In the code the configuration assign to P06 (Tx) and P08 (Rx) , when i look in the...
I'm implementing an application which uses the Secure bootloader with bonds. What happens if I create a bond to a device in application mode and then switch to bootloader...
We are designing a circuit that will be supplied from lipo battery, vddh. I am wondering how decoupling capacitors on vdd will impact as it is suggested (in errata 202) to...
We are using pc-ble-driver-py on our Ubuntu host machine which is connected to the nrf52832 running connectivity firmware and we are able to run the examples, how could we...
Hello,
I have got a quick question regarding a potential workaround-setting for the BLE_HCI_DIFFERENT_TRANSACTION_COLLISION-error.
Here is what I am currently seeing:...
Here i am attaching the my working code of the application.in my application i am using the two peripherals one is TWI and onther one is UART.i interface some sensors with...
I have a wireless project. Requirements as:
Support platforms: Desktop/Laptop and mobile, Pc/Mac/IOS/Android. etc.
many connections: flexible but can support 100+...
We are programming our nRF52 based boards through USB via the P20 connector on a Nordic nRF52-DK board. However when there is a problem with our board, e.g. if it did not...
Hi,
I am working on an application using NRF52810/NRF52832 without Soft Device (I don't need BLE for this app), on a custom board. I am using the SDK15.
There is no external...
Hello,
I run the example given in SDK V15.0.0 to measure Vdd of nRF52-DK:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE(NRF_SAADC_INPUT_VDD);
I don't change the default...
