I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi,
I have been playing around with the nRF9160 DK trying to get it reading a range of sensors, so far with success, however I have found an issue which has stumped me...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We connect to the broker through the MQTT command...
Hi,
I'm trying to compile Zigbee examples nRF5-SDK-for-Thread-and-Zigbee in Keil but faced some errors.
This is the error I got. This is the exact location of the project...
Hello,
I'm designing a device based on nRF52840 SoC that receives a configuration (set of 50 parameters) from an app which downloads the configuration in JSON format from...
Hi, I tried to run an adc example ( https://github.com/haakonsh/NCS_SAADC_example/tree/master . ) for nrf5340 in another post ( how-to-configure-the-dma-in-adc-and-how-to...
Hej!
Upgrading from SDK16.0.0 to SDK17.1.0, concerning sdk_config.h in my application: I worry that some new options could have been introduced while some old ones might...
Dear support,
I tried to follow the video here for adding service to https://webinars.nordicsemi.com/developing-bluetooth-low-energy-6 ,
Read and notification works fine...
I think I may have found errata. Using the combination in the title I can enable output, verified at the pin using OUTSET. Once the softdevice is enabled the same command...
Hey,
Currently using a nRF9160 DK with an iBasis eSIM (connected to AWS/Azure)
Any good input on using the eSIM as an root of trust? Implementing it as a security layer...
I have been working with the Azure iot hub sample appilcation since version 1.5.0 and use an SD card to store the authentication certificates and other information to connect...
We are having trouble getting the NRF52833 to operate in a low power mode. It always seems to be drawing 1-2mAmps.
Application: Nrf52833, Central host, scans 100ms every...
Hello,
I am using nRF52840 DK board and nRF5SDK17.0.2.
I am trying to code to print data on UART so I have added below folder path into user include directories:
...
I want to add iBeacon frame in eddystone.
nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_eddystone
in this along with eddystone advertising i want that ibeacon...
Hello,
I am new to Nordic. I was trying to find a sample code that has implemented NVS / EEPROM (I don't want to use external EEPROM). But I did not find any example that...
Hi,
I have the SLM application running in a custom board with uses the NRF9160. The SLM is driven an external microprocessor within the same board. Everything seems to work...
