I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
I'm having a hard time wrapping my head around how to configure my LIS2DH accelerometer for 6D orientation detection with Zephyr. How would I manipulate the registers of my...
ncs 1.5.1, using SES, the example for zephyr samples/boards/nrf/nrfx/src/main.c github URL: github.com/.../main.c
does not work for me; while the 'button_handler' gets called...
Hello, I want to make multiperipheral system with nRF52840 (Im using 4x nRF52840DK). Im using latest SDK17. I wrote criteria i want to put to this system below:
1. Devices...
My question is very simples. If I have to start with a new design, is better for me to use the softdevice implementation or is better to use the zephyr once ?
The evolution...
Hi team,
My customer is using DTM for the test and they want to know how to change PHY and radio channel setting for the DTM, could you please help to clarify?
Thanks...
in sample ,prj.conf had configure ble device name using below define :
CONFIG_BT_DEVICE_NAME="Nordic_UART_Service" ,
in hci_core.c function bt_enable() use set_bt_name...
Hi Nordic,
In this question: https://devzone.nordicsemi.com/f/nordic-q-a/56529/how-to-check-or-read-the-list-of-bonded-device-from-nrf52832 It was discussed to update...
Is it possible to use both Zigbee & BLE MESH at same time?
Actually we are planning to use NRF52840 for our next project. In which BLE MESH will be used for BLE mesh device...
Hello,
I am using NCS v1.5.0 and my application runs in non-secure mode, and uses a custom SPM. Initially all build and ran correctly, and the SPM fit in a 32 KB partition...
Hi Dev team,
I am running an application using Thingy91 along with MQTT.
I am having a simple logic of storing data for a while and then sending it out through MQTT. For...
Hello,
I've been testing 802.15.4 single PHY (no softdevice) and analyzing packets on a TI CC2531, just to check interoperability. Things seem to work well when the packet...
Hello Everyone.
I am a newbie in NRF52840 development. I have one NRF52840 device as a central device and many peripherals are getting connected to it (Max 6). Lets say...
I am currently using the 17.0.2 SDK to develop some code on the nrf52832 which involves streaming data via SPI to an external flash. I need to stream this data at a ~50KHz...
hello, I have a question need you help.
SDK:nRF5_SDK_14.2.0
MCU:nRF52810
My product is used as a central.
When the voltage of the battery supplying the product is...
