Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hello Team,
First of all thanks a lot.
I learned so many things from your Nordic devzone:)
My problem: I have uploaded the blinky code using pca10040_s132_ble [ secure_bootloader...
Hi a bit a noobie here, but I can't connect to my nRF52840 on my custom board that I made. I have tried both an ST-link V2 with openocd, flashing it into a black magic probe...
This board is no longer recognized by SES to program code.
9:09:21.82 d:\> nrfjprog --recover ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR...
Hello, all.
I would like to connect one board that transmits data using the ble_nus , such as in the ble_app_uart example, to another that receives the data and sends...
I have been using nrf52833 Devkit with softdevice nRF5_SDK_17.0.2_d674dde have nrfconnect v3.6.1 when i merge hex file of softdevice 140 + ble_app_template then the following...
Greetings,
I've seen multiple references on how to change to the 2Mbps PHY after a connection is made, and I have that working.
Now, I'm trying to advertise at 2Mbps and...
Hi support team,
I am a beginner with Nordic nrf5 sdk for mesh. I begin with the sample light_switch. Currently I want to toggle the status (on/off) of the unprovisioned...
Hi
We need clarification about Nordic Advertiser Extensions (Instaburst) .
1. The document ( Nordic Advertiser Extensions (Instaburst) ) says that the maximum theoretical...
Sir,
How are you ?
I developted an BLE application (Segger Nordic SDK) to a chinese module and worked very very nice! I installed in 40 modules. All working
No i ordered...
Hi there,
I've just installed the "thingy91_at_client_2021-03-04_8e8c6089.hex" AT command client app on my Thingy:91 and I've connected to it via the nRF Connect LTE Link...
Is nRF5340 RF port S-parameter available?
I am looking for the S-parameter of the RF port so I can figure out the best matching circuit for my layout. The only S-parameter...
Hi ,
I want to build .. \mesh\bootloader, I know must use CMAKE, but I do not know how to use CMAKE?
Could you tell me or show me the step,please?
Thanks!
Looking for the nRF 9160 SMS sample mentioned in Getting Started. I can not find it in the folder mentioned.
This sample can be found under samples/nrf9160/sms in the nRF...
Hi,
I am using nRF52840 on my custom board and Mesh SDK 5.0.0. I am testing the Mesh Light Switch example on my custom boards(one for client and two for server)with battery...
How can I send data from nRF5340 to Raspberry Pi? Do I need nRF52840 Dongle dongle attached to raspberry pi? What functions should be used to send from nRF5340 and receive...
