what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
Hi,
I am following a client case that they have issue on accessing SD card via SPI port.
I used the sample project fat_fs on nrf9160_pca10090 DK and used SPI_3 to access...
nRF9160 DK schematic sheet 2 missing pin names for WP and HOLD of nRF91_EXT_MEM in the On-board interface (far right page 2)
could someone post what nRF9160 pins are used...
Hi,
I have written one application with logging disabled to save power.
However, when I tried to debug the code with Ozone, during startup, it raises BusFault exception...
Hi,
I am currently working on generating a dfu over serial uart by testing with the ble_app_blinky example given in the SDK 15.2.0. Currently the ble_app_blinky hex file...
Hi ! Using nRF52840 whith SD140 as central and 6 link count I research :
changing the NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 2 does not change "Window size" on CONNECT_REQ...
Hi,
I messed up my SES project and now the debugging session doesn´t start and the debugger does some weird stuff and doesn´t execute my application.
I also tested if...
Hi,
I am using the DFU example given in the SDK15.2.0 to try and update the application on my NRF52840. Currently, I have been able to update the application to run the...
I use many SEGGER_RTT_WriteString and SEGGER_RTT_printf sprinkled throughout my code which was very helpful for debugging and monitoring, however, we're getting close to releasing...
I have attempted to update the firmware on the Nordic Thingy:91 via usb connection to my laptop running CentOS 8, however, finding great difficulty updating the firmware through...
My stm32 (as a master) uses SPI to communicate with nrf52840 (as a slave) When my nrf52840 wants to send data to stm32, it will pull a GPIO to let stm32 generate a GPIO interrupt...
I am using a BL632 DK from Laird, trying to erase the onboard 52832 device. I can connect to the target, but it fails when try erase all.
Results from connect target:
...
Hello,
I am trying to adapt the new Mesh Sensor Model examples in v4.2.0 of the SDK for Mesh to allow sending >1 byte sensor data over the mesh network. I have two nRF52840DK...
Hi
I am using nrf52832-PAC10040, SDK : RF5_SDK_17.0.2 .
USE CASE:I need to make connection between HID keyboard with Central(ble_app_uart_c) . And send/receive data...
I got a nrf52832 custom board to communicate with LIS2DH12 accelerometer by I2C(TWI).
I edited part of the code from "twi_sensor" project in NRF5_SDK version 17.0.
I tried...
Hello,
I have an external flash w25q32 spi nor flash. I tried to communicate with my flash using spi_nor driver code in zephery however it didn't detect the external flash...
