Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Which type of PCB antenna should i use for BLE beacons based on nRF52832, nRF52840 and nRF52805 for longer range applications.?
Can i use the same antenna used in nRF52DK...
Hi All,
There are few chips that Nordic supports Direction Finding.
nRF5340,
nRF52833
nRF52820
nRF52811
Is it possible to know the recommended chip I should...
hi all,
NRF_ERROR_INVALID_STATE is coming when i initialise Ble_stak_init form nrf_sdh_enable_request() function.
I initalised ble once and disabled using sd_softdevice_disable...
Hello,
I am developing on the Garmin LIDAR-Lite v4 , which uses an nRF52840 internally with the programming pins exposed. I am able to run my OpenThread application on this...
Hi
while developing I've discovered that the current tickless implementation using RTC causes the idle task to loop for one tick before waking the next task up.
I've instrumented...
Platform: nRF52840 { development kit } SDK: nRF5_SDK_16.0.0 Can sdk_config be used to remap any pins for used a SCK and MOSI and MISO? Specifically, can the following mapping...
Hi all,
I'm running into this error when trying to compile anything for the SPI library in Cmake
CMake Error at ../../../cmake/extensions.cmake:372 (add_library):...
SDK v16.0 NRF52832
Hi
We have been using the the NRF Bootloader for sometime, but we have encountered an issue where if the DFU (Serial) is interrupted (ie, USB cable...
Hi,
I've been using the Thingy:91 to communicate with some sensors. One of this sensors is causing us some trouble: sometimes the I2C communication with him seems to fail...
Hello
I would like to commission my Thread network but my Thread network is isolated (I have no wifi) but I have bluetooth which works in parallel to the Thread network...
I tried to use pin_change_example in SDK to catch Interrupts (at first line) but I'm missing lots of them, I don't want to use PPI mechanism I just want to run my ISR in time...
Hi All,
I have developed my application for the nRF52832 (SKD15.2) on top of the TWI sensor example. I moved from the legacy TWI driver to nrfx due to the data length limit...
hi ,our company is developing a product.the product have a nrf52832 and nb-iot module.now have one case: system start normal and mobile connected the ble,but the gap will...
Hi,
This is not a ticket!
I just want to share a simple application that I have built for the nRF52840 . It's a USB keyboard.
The example also shows how to handle buttons...
Hi all ,
I'm using SDK 15.0, working on ble_uart.c
I need to change the DEVICE NAME of the frequently.
Can you please tell me how to change the the device name and store...
