Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi
I face ble disconnection issue.
we use external crystal 32.768khz. However, when I check it , the load cap is wrong. It should be about 9pF but it is 1pf.
The frequency...
Hi,
When factory resetting the flash storage, I delete all records, and then call fds_gc(). However, the page that's used for garbage collection still contains a copy of...
Invitation : The provisioner invites the unprovisioned device to send its provisioning capabilities information.
Firmware version from this examle: https://github.com...
Hi.
I've bought the nRF52833 DK and I want to use it with Mbed OS.
But I'm not getting it to work. If I compile the "mbed-os-example-blinky" program for target nRF52-DK...
Hello.
I would like to ask about writing data from Smartphone to Thingy. How to change characteristic using setOnCheckedChangeListener.
Is it correct way to change characteristics...
Dear people ,
nRF52840 and 15.2 version
I have uploaded the program ble_app_hts in my NRF52840. After which I uploaded ble_app_uart but I still get the "Nordic_HTS"...
I am trying to switch off the 3.3v power domain to save power.
I can disable it by using adp536x_buckbst_enable(false) in board_secure.c but when I try to use the same...
Hello
currently we are developing a hid bluetooth mouse using nrf52832 and SDK 15.3. We are using app_scheduler to send movement data to the host pc, but when we enable...
hi,
Is there any working PDM example for nRF52832? or can anyone give a sample initialization code for PDM with easyDMA using the inbuilt nrf_pdm_drv functions?
Regardss...
I am tried porting the USBD to mesh serial example according to usbd_ble_uart this days, and some functionality are test fine including Tx and Rx between Provisioner(USBD...
I teach high school robotics and after the BLE blinky program which works greata with mobile nrf-connect, I wonder what people think is the best, generic BLE
Central and...
Hello,
Can you please provide the input impedance or the S-parameter file of the impedance for the nrf52840 for receive mode, and also at tx power levels of -40dBm, 0dBm...
AD value and voltage conversion between the calculation formula
adc_config.resolution = NRF_ADC_CONFIG_RES_10BIT;
adc_config.scaling = NRF_ADC_CONFIG_SCALING_INPUT_ONE_THIRD;...
Hi, I have a few questions about the nRF52833 DK.
1. Can I fix an antenna array onto the DK to make it a receiver in Bluetooth 5.1 AoA applications? I can see that there...
