Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello, I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated Continuous...
Hi all,
I'm having a tight deadline upcoming and have run into an anoying problem.
I'm using this NRF51 breakout board: ohtcom.com/.../nrf51-m0-module
I ordered a...
HI I am trying to make 5 characteristics on Nordic and my program does not compile for NRF51822 QF AA or AB. but compiles fine for QF AC. what could be the matter. I get an...
Hi,
At command, I'm sampling ADC for a short period of time. What I noticed is that the current consumption of the chip goes up 2mA, even after the sampling is stopped...
Hi,
What is the actual difference in hardware between the two chips? I know they support different soft devices but is there any actual difference in the hardware? Or is...
Does having monitor mode debugging or using RTT print statements increase the quiescent current of the nRF52 even when the debugger isn't connected? I am using S132 SoftDevice...
I'm in the process of porting code from a PCA10000 rev2 board to a custom board, using the ISP130301 integrated MCU (contains a rev3 nrf51822 IC). I'm using nrf51 SDK 6.1...
Hi,
I use an nRF51822 QFAC A1 and my goal is to disable BLE in a powerdown mode, then when I press the pushbutton I want to restart BLE.
Tried using BLEDevice::shutdown...
Hi,
I'm using nrf52 dk(PCA10040). I want to disable the SAADC between readings to save power. I am calling the function nrf_saadc_disable() to do so. It seems to disable...
Hi,
I am having some trouble to make NFC Tag emulation working with "ble_app_hrs_rscs_relay" example application in the nRF5 SDK v11.0 on a PCA10040 board. Actually I did...
Hi all,
i have a little problem with the #define NRF_LOG.
I have this warnings, and i don't know why.
Warning[Pg004]: macro parameter " VA_ARGS " is used in both expanded...
Hi,
I would like to generate PWM waves with on/off period as low as 10usec.
How to stop the PWM and restart it? I tried this but does not stop the PWM:
void pwm_start...
I am trying to advertise my eddystone UID,TLM and URL frame on advertisement. Here by board is in peripheral mode.
I used radio_notification_init() function where i have...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...