Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
After a connection long push event does not work! But before a connection long push works fluently.
I could not found the error.
Thank you for your interest.
...
Our group is trying to use the NRF52833DK do phase-based distance estimation as described in the attached paper. To do this we want to transmit packets with constant tone...
Hey There,
I have one problem more. With my .cs Script I am opening a USB Port on my Raspberry, to communicate with my Nordic Thingy 91.
I can Read what the Nordic is...
Hello,
I want to read the CA certificate stored inside the modem, unfortunately the modem_key_mgmt_read function cannot read a certificate bigger than 2kb even if CONFIG_AT_CMD_RESPONSE_MAX_LEN...
I have a few nRF52840 DK to evaluate a Bluetooth mesh application. The light switch example is ideal for our initial tests. The only thing I would like to do is to write some...
Hi,
I see that my device name is getting shortened on advertisements. I take it this is sue to the fact I have included some manufacturing data. I need both unfortunately...
In Mesh DFU, is there a way to change the public key on a set of deployed devices? I'm wondering if it's possible to rotate signing keys for our deployed devices that use...
Hello,
I'm trying to migrate my deployed devices to the nRF5 SDK for Mesh 4.2.0 (with connected nRF5 SDK 17.0.2). On the field I have several devices with nRF5 SDK for Mesh...
SDK is nRF5_SDK_17.0.2_d674dde, running on nrf52832, I migrate twi_scanner example to \examples\ble_peripheral\ble_app_gatts_c, if I set handler NULL in nrf_drv_twi_init(...
I used the "Toolchain manager" in nRF Connect for Desktop v3.5.0 to install nRF Connect SDK v1.3.1 on a macOS Catalina 10.15.7 system. This installed SEGGER Embedded Studio...
hi,
I am using nrf52840 (in a Laird module) and trying to advertise such that legacy BLE 4 mobile devices can connect. Only BLE 5 mobile can see the device (running nRFConnect...
Hi, I have a problem with the reset pin not working on the nrf52811. The firmware was developed on the nrf52840dk board and now that we are migrating to the real nrf52811...
Hello,
I have one SPI instance (instance 3, but have tried others) reading data from an ADC. It's reading data from an ADC triggered by a DRDY signal at 25khz. I setup a...
Hi,
I just enabled the CONFIG_BOOTLOADER_MCUBOOT=y for serial LTE modem application to understand the flash partitions and to perform the serial DFU(not sure if its really...
Hallo, using nRF52840 DK with Keil uVision 5.30, I try to debug the example ble_app_uart in the folder ble_peripheral, pca10056, s140. Compilation is OK, erase/programming...
