Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Issue:
The OTBR could run with RCP versions built with SDK v2.3.0 and v2.4.2 but couldn't work with fw from SDK v2.9.0. Hence, I wanted to know which of the latest SDKs...
I have been working on a project using a nrf52832 and currently have the firmware developed on nrf5sdk. I have been testing out Zephyr with this example https://docs.nordicsemi...
Hello
I'm using the NRF52840DK with a custom shield on top that interfaces to my custom board. I use it to program and debug the DUT via the DK, talk to the DUT over serial...
Hello,
I am working on an update of older FW implementation: nRF52832, SDK 14.1.0, with SoftDevice S132 and using BLE connection.
The change I need to implement is a functionality...
Dear Nordic Technical Support,
I’m currently evaluating the NFC functionality on the nRF7002-DK with the following setup:
Hardware: nRF7002-DK
SDK Version: nRF...
For power-saving we periodically enable/disable the net-core. We would like to use the WDT on the net-core
as well. Since you cannot stop the WDT, how should we handle this...
When I first set up my system I had a color code view of the RAM in my system where the colors corresponded to grouped data objects. Somewhere along the line that view has...
Hello,
I am unable to use the Segger RTT terminal built into the nRF Connect SDK for VSCode Extension pack with the nRF54L15DK.
I have configured my project with the...
Hello,
zephyr: Vanila v 4.1.0
I'm trying to run FOTA via BLE on the nRF54L15DK. I’ve configured everything as it should be, based on the sample:
When I...
Hello,
Is it possible to make the nRF Sniffer for Bluetooth LE application work on a nRF54L15?
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth...
Hi, I am testing the PaWR examples in the NCS and I have few doubts.
In this page , it says in section 1.3 that there are two ways for synchronization - PAST after connection...
From what I can see in the documentation, UART0 is used by default for "non-secure" / application logs and UART1 is used for "secure" app logs. I am needing to interface with...
Hello, I am using an I2S PDM Mic and trying to send the I2S Data over BLE using Segger Embedded Studio. The I2S Program that I have generated is working ok. I have verified...
I am using SDK 2.9.1. I wanted to follow this tutorial:
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-7-device-driver-model/topic/exercise...
Hello Nordic friends,
currently I use NRF7002-EK successfully in my bare-metal environment, but for debugging, I'm considering using the EB instead of the EK if the edge...
