Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi,
Platform: nRF54L15, SDK 2.9
The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
I have problems with nRF Connect(Android, latest Version, no version number found) to find BLE devices with 2M phy, coded phy and extended advertising. So i am running nRF...
I have made my own NRF52832 Dev board as in the next image:
I received the board, and ICs and hand-soldered them in my home.
however, I am still a newbie in nRF SDK...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I'm currently developing a BLE Long Range application based on Zephyr and the v2.8.0 version of the nRF Connect SDK. The app is based on the following nRF samples: central_hr_coded...
Hello,
I am currently stuck trying to migrate a project to the 2.8.0 version of the NC SDK.
I followed the exercice of the Nordic Academy : FOTA over BLE .
It works...
I want to automatically reconnect to my peripheral (nrf5340 DK) from my central (phone) when there is an accidental disconnect (out of range) which I am simulating by resetting...
We are using the nrf9160 with SLM V2.4.2 and Modem V1.3.6 and we can do 6 calls to the Verizon cell network in 3 minutes and 30 seconds apart with no issues.
However, on...
I am developing a BLE application on the nRF52 platform using FreeRTOS. My application involves custom BLE services and characteristics, and I am encountering a hard fault...
Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
I have a device with 3 major components:
Fanstel nrf52840
PMIC1300
spi display (Waveshare 2.13inch E-Ink Display)
PMIC:
BUCK1: power Fanstel
BUCK2: power...
I am running a modified GNSS demo code for our board. At initialization, there is some traffic going between the MCU and the GNSS chip, but when the demo code calls nrf_modem_at_printf...
I am having a problem after installing 2.9 where I am getting a problem on some projects where the nRF addin does not seem to work
When try to create a new application...
Hi, On Ubuntu, after a distribution upgrade from 22 to 24, NRFConnect has failed in a couple of ways. 1. Upon starting, the application fails with: [7982:0910/180010.628514...
