Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
Hi there, I am working on SMP client server application where I want to do the DFU of server from the client side where both the server and client are nrf52840 dev boards...
Hi,
I followed the instructions listed in Installing the nRF Connect SDK (nordicsemi.com) . Then I followed the steps in How to create and build an application (nordicsemi...
I am working on nrf52832 development kit for interfacing SX1262 Lora module via SPI. I have configured SPI 0 as follows:
Initially I am trying to read the SX1262_REG_SYNC_WORD...
Device/Board: nRF5340 DK Application: Mesh Light (Bluetooth Mesh Network)
Use Case: I am currently working on a Bluetooth Mesh network using the nRF5340 DK. My goal is to...
Hi,
We are using nRF SDK 2.6.1 and have selected the nrf7002dk_nrf5340_cpuapp target. After adding CONFIG_BOOTLOADER_MCUBOOT=y to the soc_flash_nrf example,
the code fails...
Hi everyone,
I have a problem about MBR and Bootloader memory (at address 0x74000). I am using nRF52832 S132 v6.
My purpose is that I can upgrade bootloader from inside...
I would like to wake my app from sleep (k_msleep) on a GPIO interrupt. I'm finding that enabling the interrupt draws an additional 6uA however (8uA vs 2uA without it) - am...
I would like to set a gpio pin on Radio RX Ready and clear it on Radio Disable all via PPI. Below is my code. I only get the pin to change levels when the OUT task polarity...
We are looking into the following link for the softdevice S112 API documentation however we are getting Error Code 404.
Technical Documentation (nordicsemi.com)
Can...
Hi ,
I want to enable encryption in Bluetooth communication for a proof of concept.
I have Wi-Fi Provisioning example and in that while sending the wi-fi password ,...
Hello,
We are using nPM1300 in our project.
I would like to configure it to the maximum possible discharge current limit, as there are inrush currents in the board.
...
Hello, I have a couple of questions concerning the nrf52840 dongle
1. Is the dongle supported in the nrf connect sdk? I see that the board is within the build boards,...
Hi Sir
I am using an example from NCS 2.6.0 and want to modify it to use ADC channel 6 (P0.30) to read voltage values, but I am unable to get the correct values. (When I...
Hi, I have a custom board connected with DK and i was able to program it and test some simple codes. I need to test this TWI example on my board. I uploaded it but i am not...
I am currently developing with the nRF52832 using the nRF5 SDK 14.2 and need to proceed with AES-128 encryption.
However, I cannot find the CDC (Cipher Block Chaining) library...
