Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
My issue is that even when using...
Hi All,
I am building a event driven IoT application thus using the Nordic CAF I like to know if the Nordic and/or zephyr (system) threads are running fine (if not the watchdog...
Hello,
I am currently migrating from NCS 2.6.0 to NCS 2.7.0 on my board with an NRF9160.
During that process I switched to the new hardware model and to sysbuild. As far...
Hi,
I am getting the following error: CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/extensions.cmake:2891 (message):BOARD is not being defined on the CMake command-line...
Dear Team,
This is my first embedded project.I am basically from Analog design background.
I connected the nRF52840-DK board as shown below.
I connected the board...
Hello and thanks for reading. Our device needs to act as both a central and peripheral. I have written all the peripheral code, and its all working perfectly. However, once...
Hi,
I have a project in which I'm using the nRF52840 with OpenThread and the device is configured as an MTD to minimize power usage. I have recently updated my nRF Connect...
Hi All, I am getting build errors for a project. Project specifics below: - nRF52832 (custom board) - NCS v2.6.0 - Custom board files and other configuration files attached...
My application is running on a nRF9160 using NCS v1.7.0 and modem FW 1.3.0. Sometimes, when our device is in an area with bad LTE coverage, I believe we're overflowing some...
Hi there,
I am using the NRF52840DK development board as a learing experience. I have used the EXCERCISE8 on the Nordic learning program and created a SPI driver for a simple...
Hi all, I am observing some strange behaviour on my two nRF52840 devices. They are running NCS v2.1.0 (Zephyr 3.1.99), one as central and peripheral, one as peripheral only...
Hi,
I am trying to build the pc-ble-driver library from source following the readme instructions ( https://github.com/NordicSemiconductor/pc-ble-driver ) on my Windows...
Hi,
MCU: nrf52840
SDK: nRF5_SDK_17.1.0_ddde560
I am facing such an issue, sometimes after the device's OTA success, and then I would like to upgrade to another version...
Hi. I'm on a relatively old ryzen-5 windows 11 PC and I get 30 FPS when recording power with Power Profiler version 4.0.0 and 2 FPS when recording with newer versions (4.1...
Dear Nordic support team,
I cannot enable the Nordic specific HCI command to enable the HCI survey, I always get the following error with NCS v2.6.1:
For information...
