I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
We are finishing up a project with the nRF52832 based on the Nordic Thingy. Most of what we want it to do are normal functions of the Nordic Thingy. It connects to a mobile...
Hello,
The last ticket referencing this topic is 2 years old. I thought I would ask this question since we now have NCS.
Application is a Gateway that will support Zigbee...
I am trying to fun the LTE Sensor Gateway on the Thingy:91.
The boards are missing from zephyr so I copied nrf52840_pca20035 and nrf9160_pca20035 from ncs\nrf\boards\arm...
Dear all,
I'd first like to apologize if my questions seem dumb. I'm a student in mechanical engineering and only just started getting accustomed to microcontrollers and...
Hello,
I just installed SDK and Embedded studio.
And when I try to rebuild example, error occurs.
Below is my setup information.
- SDK: nRF5 SDK 16.0.0
- Example...
Hello support,
Currently i'm working with one application using NRF52832.
in which i have to fetch data from coming from PIC controller to NRF52832 over UART communication...
Hello, I owe a nRF9160 DK version 0.8.2. The ERRATA 0.7 document says that for this version the GPS antenna does not work well. I need to use GPS for extracting PPS signal...
Hi all, I've been recently working on PSM for my device, and I've not found any resources that answer my query or provide the knowledge I need. From my reading in this article...
Hello whenever I am calling sd_power_system_off(), it gives me the following error- implicit declaration of function 'sd_power_system_off'.
What shall be the optimum solution...
I use a 3.3V battery as VDD on an nRF52832 device.
Along the line this battery might do down from 3.3V to 1.8V. Will the Internal Reference Voltage be consistent at 1.8V...
Hi,
In apply_old_config.h ,here is the code:
for example:
If I set SYSTICK_ENABLED =0 in sdk_config,here will overwrite the macro define because #if defined(SYSTICK_ENABLED...
As per the datasheet of nrf52840 any peripheral like SPI/UART/... can be configured to any of the GPIOs so is the QSPI also.
But at Pin details QSPI pins are recommended...
Hello,
We are working on machine health monitoring system. For that we are using nRF52840 SOC as Central and nRF52833 SOC as end node. We had used single Central node and...
Hello.
I'm beginner on Nordic product and checking the examples with nRF5_SDK_17.0.0_9d13099 on nRF52833 DK Board.
I tested ble_app_uart and it works. Now checking ble_app_hrs...
Hello, I am
I'm a Beginner at developing NRF 51822 My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
Recently, I've been experiencing a lot of...
Hi,
I'm trying to find a way to power down and on again a RAM section, but I haven't had any luck finding.
In the SDK examples, there's a RAM retention example only, but...
