I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi!
Can anyone from Nordic pinpoint where exactly in buttonless project or bootloader project NRF_DFU_SVCI_ENABLED definition is used? I mean 15.0 and 15.2 SDK.
I have...
Hi, i need an advice.
It said in nRF51822 datasheet at p.11.1 (PCB guidelines) that "The supply voltage for the chip should be filtered and routed separately from the supply...
I have upgraded to the more recent J-link RTT Viewer.
If I start Debug Session in uVision and run RTT Viewer, I can connect just fine and have checked the Existing Session...
In the nrf5 sdk (version 11.0.0) there are three different modules which, as near as I can tell, do the same thing. These are:
pstorage
fstorage
ble_flash
...
hi........... nrf523
how to read the data from peripheral and send the data over ble using ble uart
i have merged the two programs ble_uart and twi sensor ,what changes...
Hi,
I'm trying to flash the mesh lightswitch example on Bluemod S42 custom board, please help me with what are the steps to be taken to flash on custom board.
Hi,
As the tile says, I'm using BPA600 capturing mesh logs and analyze.
Since BPA600 needs to configure "MeshOptions.ini" to be able to decode the logs, it needs "IVindex...
Hi
I would like to debugg my Nordic (nRF52832) custom board at 1.8V with a 6 pin Tag-connect connector ( see here ) and have a couple of questions regarding...
Hi,
I'm trying to compile a simple example (light_switch_dimming_server_nrf52832_xxAA_s132_6.0.0) for Bluetooth mesh with Segger embedded studio. I'm having a hard time...
Hello,
I have a twi module developped using sdk v13. I want to upgrade it to the sdk 15 to integrate it to a mesh project.
I changed all nrf_drv functions to nrfx same...
can I make indoor localization with nrf52840 DK board without an android app,
suppose I am using 3 devices for localization of the 4th device, and I need to get RSSI of...
I want to make infrared transmission and reception function with nrf51822.
I want to know how to make TImer part using NEC protocol.
Tell me how to implement this feature...
Hi,
I am working with nrf52832 DK,softdevice s132.SDK15.
I was following "nRF_Sniffer_User_Guide_v2.0.pdf" to set up nRF Sniffer.
But in the Wireshark Application under...
Hi there,
This is a general question about addresses types in Bluetooth mesh and specs:
As far as I know, Bluetooth mesh specs talk about the 32767 nodes in the theoretical...
