I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
While developing a set of C++ tools to simplify configuring and managing BLE on NRF52 chips, I've encountered an error code returned from the advertising module's ble_advertising_start...
Hi, I have several services running in the application. one of them is DFU.
I have to hide / stop DFU service for example when the SOC of the battery is less than 50%. And...
Hi,
I am working on nrF52832 as a gatt peipheral (server)and have a requirement to send 12KB of data over a custom service. I have done the following:
1. Created a custom...
Hi Nordic:
1. Does NRF9160 modem 1.3.1 support CSQ command?
2 Is there a command to get SINR signal?
3. NCSv1.8.0, modem1.3.1 %XRFTEST (AT%XRFTEST=2,1,0,0) Can it can...
Hi,
we're performing an evaluation of using an nRF528xx module with 802.15.4 stack to replace a 3rd-party radio module. There will need to be an AT command protocol for...
Hi i am using nordic nrf52840 chip. and SDK17.1 i am using.
in that under secure bootloader code i am trying to use the nrf_crypto_hash_update() function to calculate...
Hi,
We need to update the firmware of the device through IOS-nRF-Connect-Device-Manager, but the language currently used in our old project is objective-c. IOS-nRF-Connect...
hello ,
We use the nRF9160‘s GPS. We see that the 9160 Thingy use a GPS LNA between the 9160 module and the 9160 GPS antenna?
We want to know, whether we can do...
Hi,
I know that the Bluetooth mesh cannot use long range, but I want to know whether the output power of the node can be controlled to adjust its broadcast range？
Thanks...
hi support team,
for ncs, how to add dir to segger IDE like this one.
for example, like keil IDE separating those two .c into two folder in segger.
Regards,
William...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
The instructions at https://github.com/NordicSemiconductor/pc-ble-driver do not allow building the driver or the examples on a Windows system. Following the instructions takes...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, it connects with Mobile or Tablet using Pairing with bonding...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
