Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi, I'm designing water meter modem using the nRF52840 + nRF9160. I will apply nRF52840 as a HOST CPU and the nRF160 contol by nRF52840. (please refer to attached picture...
Hello,
I am interfacing a NRF52832 with a PCF8574 I2C slave using SDK 15.0.0.
As per the datasheet, the device will send the data to the slave after it receives the write...
Dear Sir,
I designed a new pcb based on nrf9160,
The boards are populated with cipsim.
When running the MQTT_SIMPLE project i get the following error for the 2 boards...
Hi,
We are upgrading our product from SDK 15.0 to SDK 17.0.
In the old SDK there seems to be one file abailable: ../SDK_15/External/nrf_cc310/lib/libnrf_cc310_0.9.9.a...
Hello:
We are developing a DFU bootloader for an NRF52 product that supports USB and BLE upload methods (they are 2 separate bootloaders from a common source). Both work...
I am hoping to pass data from the nRF52840 to the nRF9160 over UART_0, on a custom PCB. For context, the aim is to pass data at a rather quick rate and good reliability. The...
HI,
I want to make a receiver to get BLE packets on any channel.(NO SOFTDEVICE)
I fail to fullfile it yet by reading <nRF52810_PS_V1.3.pdf>.
Any other hands can give...
Hi,
I am working on the asset_tracker application example on a Thingy:91 device. As I understand it, to activate the GPS it is necessary to keep the button pressed for a...
Hi,
In nrf9160 I want to check the communication of LTE device.
I have installed nRF Connect for Desktop, Getting Started Assistant, LTE Link Monitor, & Programmer.
...
Dear,nordic:
Please help me solve the exception encountered during the MQTT connection
SDK : ncs v1.2;
samples : asset tracker;
path : ncs\v1.2.0\nrf\applications...
Hello everyone a basic question but just to be sure.
I would like to make a custom board and I want to program this board with segger Embedded studio, should I just have...
Hi!
I managed to get the device connected to the nrfCloud and started receiving messages from it.
Anyway, the embedded antenna cannot catch the signal very strongly. Can...
Hi,
I am trying to test the asset tracker code on the nRF9160DK from the precompiled hex files from [ images_dfu_hex/nrf9160dk_asset_tracker_dfu_2020-04-29_bc7ade8b.hex...
It was my idea to compile the mqtt_simple vom v1.3.0.
I spend now one week with your sdk. I tried it with SES and also with command line. Absolutly nothing worked.
The...
