Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am using battery (3V) to supply nRF51822 system and the circuit is made according to DCDC mode circuit. My question is :
what is lowest voltage the battery can...
I have two p_storage_param modules param and param2 . param would store 3 blocks of 16 bytes and param2 would store 10240 bytes (10 pages). I called pstorage_register (param2...
Hello,
I followed both tutorials about using Eclipse GCC and migrating to peer manager.
I get no error when I follow them individually, i.e. when I use the project included...
Hi,
I developed an application based on s110 using the nrf51 DK and it works fine. The DK is based on a nrf51422 QFAC which is the biggest one in terms of memory sizes. Now...
Hi,
the mesh_dfu.c requires the definition of tx_config_t, which I can't find anywhere in the repo branch sdk-8-support. Same with RBC_MESH_EVENT_TYPE_DFU_SOURCE and other...
Hello,
This is in reference to the following:
devzone.nordicsemi.com/.../
The post talks about the maximum size of application that one can in order to be able to...
I'm trying to get the PWM example to compile in SDK 10. However I cannot get app_pwm.h to compile. I get the following errors:
expected expression before '{' token ble_app_hrs...
Hi All,
We are in design Phase of our product and would like to use NRF52 Chipsets for it. Please Clarify our query regarding it.
I have two Nordic NRF52 Chipsets , One...
Hello:
Im using SDK 10 with softdevice V130.
Im opening UART:
uint32_t err_code;
const app_uart_comm_params_t comm_params =
{
RX_PIN_NUMBER,
TX_PIN_NUMBER,...
Hi,
In nRF52832_OPS_v0.6.3.pdf chapter 16 Power-Power management.
It describle as follow:
Automatic switching between LDO and DC/DC regulator based on load to maximize...
Hi all
I found the following thread that mentions that the "radio test example" can be used for FCC testing:
devzone.nordicsemi.com/.../
Now the certification lab...
Hi,
We have the samples of the NRF52 in CSP, but we don't find the documentation concerning the pin assignments.
We would like to do a routing with this chip, is it...
I am trying to incorporate our Manufacturer name to the Device Information Service. I am working on the ble_app_uart example which does not include the file ble_dis.c nor...
Hi Mate,
When I test the example of ANT which is named as hrm_tx(heart rate transmitter), after I programed the ANT_s212_nrf52_0.5.1.alpha.hex and the application of hrm_tx...
I'm running a BLE application on the nRF51822. And I have an application timer to keep track of the real time clock. However, when I receive a BLE_GAP_EVT_DISCONNECTED event...
