Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
I'm using nrf9151 and trying to upgrade from ncs3.2 to ncs 3.4. I have two builds, one with log disabled, other with rtt logging enabled. Both builds are working, but I can...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
When I create a new build ciónfiguration in nrf connect I get this Loading and the new configuration is not created itself.
This error is displayed in the VScode.
Could...
Hello, I noticed that the SoftDevice Controller for nrf5340 in nrf Connect SDK 3.1.0 reports a bluetooth version of 6.1 (LMP Version 0x0F), yet the QDID for it ( Q360820)...
Hi,
NCS v3.4.0
BLE peripheral_uart example
nrf54l15 DK with ns config
in the Chinese (double bytes) Windows, need to add encoding="utf-8" in tfm_parse_manifest_list...
Hi,
My central device is running into Bus fault when continuously sending data to multiple connected peripheral device and any of peripheral device got disconneced. Issue...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
I hope, as a non-EE, I'm clear with my challenge ...
My student EE designed a small PCB with a couple of sensors (CO2, temp/humid, microphone) with an nRF52811. The boards...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
how to configure uart communication between nrf54l15 and tc334 via uart and i need to control my nora b2 evk leds based on mesage from tc33 using tlv can anyone give me idea...
Dear Nordic team,
Please tell me the theoretical power consumption of the nRF54L15 when using CH—both for the initiator and the reflector.
Best Regards,
Riki Yosh...
