Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
I don't know who's in charge of Dev Academy, but the nRF Connect SDK Intermediate Lesson 9 -- Bootloaderse and DFU/FOTA section looks like it was written as a back burner...
Hello, I am trying to save some sensor data based on my current state of the device. I want to log IMU data and timestamp into my external flash (MX25R64) with littlefs file...
I am using a custom board with an nRF52840. For OTA updates, I’m using SDK 17.1.0 based on the sample codes:
Bootloader : secure_bootloader
Application : A custom...
I am developing with thingy53. I would like to enable BLE function, MCUboot and littlefs file system at the same time. I am using SDK and toolchain v2.7.0 and sysbuild as...
The samples "nrfx_gppi/fork" and "nrfx_gppi/one_to_one" are both broken and fail to compile. I have confirmed this for NCS 2.8.0 and 2.9.1 on Linux, and 2.8.0 on Windows....
Dear nordic team,
even if enabled for mcuboot via CONFIG_WATCHDOG / CONFIG_BOOT_WATCHDOG_FEED, our device performs a reset when swapping the image. More precisely: when...
When I build my first blinky sample, I met a error and correct it with ( https://devzone.nordicsemi.com/f/nordic-q-a/120279/update-to-ncs2-9-1-compilation-error/529668) ....
Hello,
We use NCS2.9.0 and NRF54L15-DK do the matter development, and we use template demo, just enable CONFIG_CHIP_DFU_OVER_BT_SMP in root prj.conf, then we do the ota...
Hi,
I am currently evaluating the new nRF54L15 DK development kit.
I installed VS Code v1.96.4 with nRF Connect for VS Code Extension Pack v 2024.9.5 . I am currently...
Hello,
I'm trying the Thingy 91X but I'm having a few issue with the demo application that connects to hello.nrfcloud.com:
After flashing it with the Quick Start from...
Hello,
I have a custom nRF52820 board powered by a coin cell, and I want to measure its power consumption using the Nordic Power Profiler Kit 2 (PPK2).
Could you please...
I met some problems when add build configuration to my first application. I used the blinky sample template. And the device a nRF5340 DK. My PC can detect my devices. But...
Hello everyone,
I'm working on a project based on the nRF52840, and I'm using nRF Connect SDK 2.9.0. The project uses MCUboot, but the firmware image is signed externally...
Hello, I am using NCS 2.9.0, an nRF5340, custom board files (see attached), and no external flash and I would like to use simultaneous DFU over BLE. I believe this should...
