Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi everyone,
I have a quick question regarding the dynamics of the t_conv for when having multple channels of the SAADC. In brief, I have 2 channels set up to sample at...
HI All,
I was trying to establish communication between my thread device and remote server using RPi and nRF5340DK. For that I took the echo client sample and modified according...
Hi,
We need to communicate with a legacy patient monitor device. So we need to use this NRF52840 device to send out packets and receive packets as per our legacy device...
Hello Nordic
I am working with nrf52840 and nrf52832 on pcbs, i want to use the nrf21540 with my pcbs to extend the strength of transmission.
I have read this data...
Hi there,
I'm trying to implement "poor man's gang programmer" in the following way -
On the edge of a 16 PCBs panel, there's a 2*10 pins row easily accessed by 2...
Dear All,
In our scneario, we have 10 pcs Jetson Nano DevKit based cameras in each site.
One of devices will be connected to Internet by LTE Module and act as a gateway...
Hi:
I am trying to get continuous notifications using pc-ble-driver with 52840 dongle from a Nordic NUS board. I set the MTU size to 240. After getting 9 notifications...
Hello, I want to modify ncs\v2.2.0\bootloader\mcuboot\boot\zephyr main.c code of BLE OTA bootloader, but I need to move its code inside my application firmware repository...
Hi,i use nrf52833, I configured P0.05/AIN3 as a NOPULL INPUT(nrf_gpio_cfg_input(5, NRF_GPIO_PIN_NOPULL);), But I found a weak low level in this IO port. What is the problem...
I am using a nRF52811 with nRF5 SDK 17.1
I have set the PHY to BLE_GAP_PHY_CODED, I believe this uses S=8?
Is it possible to select S=2 with this SDK?
Thanks
Hi,
is it possible to build the nRF5340_audio application for the nRF5340-DK?
What I'm currently is investigating is the possibility of finding and connecting to other...
Hi,
I am software engineer working in Philips.
I am trying to transmit 21 bytes of our payload data (fixed payload length).
I have the following configurations done...
I am attempting to connect a nRF52840dk to Azure IoT Hub using OpenThread and TCP. I combined the azure_iot_hub and azure_fota samples into one project, which ran successfully...
I tried to find simple examples to use SPI in nRF9160DK but all the examples has issues. I did connect using raspberry pi to my modem with no issues but when I use nRF9160...
HI
I had some great support in t his ticket so I will try my luck again.
We want to migrate our application from SPM to TFM. We use SDK 2.1.0. We communicate with the...
