Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
Hi all, I have worked on a Central device, whose objectives are to scan specific beacons (filter using MAC address), make broadcast and establish connection with specific...
I'm developing with a Thingy:91; here (New Zealand) we have both M1 and NB-IOT but in some locations where the product will go there's only NB-IOT so I'd like to verify the...
I have a nrf52832 custom board that I program using sandeepmistry Arduino core. Nothing to do here, I know it's Arduino but everything still works under the Nordic basis in...
I can't seem to connect the Thingy 53 to my VS studio. I am able to connect the thingy 53 via phone and I can connect it on my NrF programmer but I can't seem to find it in...
Hi All. If I wanted a book to learn embedded C programming focusing on nRF52, which one would you recommend for a starting level? And for the intermediate level? Thanks
What are the limitations on drawing current from the nRF52840 VDD pins? Are there continuous and transient limits on how much current can be drawn?
We are powering peripherals...
Hello,
I am working on adding BLE central capabilities to our device by using the ble_app_multilink_central example project as a template. Currently I am adding the expected...
Hi,
I development a elock device to use nordic 52832 chip. I want to transfer some information between phone app and my device. Like UUID / user account / user password...
Hi, My PC have already installed the nrf connect sdk with version v1.2.0. How can i update the nrf connect version to v1.2.99-dev1? Please give me a few complete steps .
Hello everybody, i am trying to use BLE central uart sample software in zephyr, on nrf52840 dongle. I mapped the uart outputs on pins 20 and 24 of the connector, made the...
I have created custom characteristics by
BT_GATT_SERVICE_DEFINE ( vnd_svc ,
BT_GATT_PRIMARY_SERVICE (& vnd_uuid ),
BT_GATT_CHARACTERISTIC (& vnd_enc_uuid . uuid ,...
I am using the current nrf-sdk v2.1.0, which includes the matter version v2.1.0 from the Nordic repository.
I encountered an error that setting CONFIG_DEBUG will result...
Hi
I have successfully used the TIMER & GPIOTE to generate dual tone frequencies for a BFSK project. 200kHz & 400kHz. ( 50% duty cycle square wave)
I wonder if the same...
