Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
Refer to nRF52840 Technical Manual USB 2.0 (full speed (12 Mbps) controller) The USB2.0 rate can be up to 480Mbps. We have a product whose USB transmission rate must not be...
I have created a program code on the Adafruit nRF52840 express in the Arduino IDE. I want to read this program code (including bootloader) via my j-link edu mini and save...
I noticed that the nRF Connect SDK has kept up with ZBOSS updates throughout the year. Is there a plan or recent releases with regard to the "nRF5 SDK for Thread and Zigbee...
Hi! I'm working on a custom board with nRF9160, I want to flash it with the asset tracker sample, however, I do not own a J-link device. What I have is a FTDI USB-UART converter...
My Thingy:52 is version 1.01. I haven't used it for a while and after charging, it didn't seem to be advertising. It was soft-flashing a green LED. I decided to program it...
Hi,
i am working on nrf52dk. i want to include "pwm" example in "ble_app_uart" example . i have included all the header files. and functions in "ble_app_uart" example. ...
Hi,
what is safe temperature range for nRF52840 - nRF9160 UART communication on 115200 baudrate without external crystals for HF clocks please ?
Thank you.
Hi,
I'm trying to program a custom board with a nRF52810 via nRF Connect. I keep getting the following error messages:
I followed this post and tried the following commands...
Hey guys,
I have nrf52832 custom Bluetooth module. It is stand alone nr52832 module . I just want to toggle any gpio on this module .
Can you guys tell me which library...
Hi all,
In my project, I make 2 SPIM and 1 UARTE works well.
Currently I want to use 1 TWIM, so I add lines below in proj.conf
However, I get errors: gen_isr_tables...
If nRF9160 stay almost all day in sleep, wake via RTC for a period of 1 minute and in this 1 minute period only make a GPS cold start, get the GPS coordinates and transmit...
My device is the slave, that is being connected (not always in the same order) by 2 masters.
I would like to create two different connection ways/points to distinguish between...
Hello.
1. For nRF5340 DK, in normal voltage mode, I use putty(windows) and minicom(Ubuntu) to view the printk logs, it works fine.
In high voltage mode, which software...
