Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
I have a custom board with a nrf9160 on it that has been working for the last three months but last week when i was evaluating low power modes on the board i couldn't talk...
Hi,
i am using SDK version 2.1.1 and recently we had a problem due to the errata 160 which is fixed also in SDK 2.1.4
I am using Toolchain Manager 1.5.3 and i cannot select...
Hi,
we plan to use the nRF52832 in a new project, where we will need ANT support.
I've seen that it is possible to use the nRF5 SDK and the SoftDevice 332 to have ANT...
Hi everyone, I have a problems when I build custom board NRF54L15. I build this project for custom board for nrf52833. It's okay and no error. After that, I change this board...
Hi!
I am testing the nRF54L15-DK with 2.9.0 SDK and have some questions:
1. MX25R64: - why is it used in 1-bit (spi) and not 4-bit (qspi) mode? - OTOH this setup saves...
I have issue in newest SDK 2.8 of nRF Connect for VS Code. When I change something in prj.conf or in the source code, I often have to build and compile two or more times to...
I have looked at forum_post_1 , forum_link_2 and forum_link_3 . In short, I am following instructions for my_dongle . I have ncs 2.6.1. I have clones of nordics git repos...
I notice in github.com/.../nrf802154_sniffer.py that there is a line saying: TODO: Add toolbar with channel selector . I know extcap supports these toolbar controls and a...
Hi
At nPM1300 product specification V1.1 page 148(8.1 Schematic)
The control I/F between nPM1300 and nRF5x is TWI(I2C), and there is four signals(SCL, SDA, Reset, INT...
Hi guys,
I've been working with the NRF52832 in the past days and I'm having issues with the GPIOTE interrupts.
It seems that there a latency of around 30us until the...
Hi! I created a unittest in my project using Zephyr CRC Unittest Example . It passes nicely using command line. However I cannot fix squiggles error in test code. I get following...
I am using NRF52833 Microcontroller to read data from the PCR based radar sensor. I am using NRF Connect SDK Version 2.6.1. I need help regarding reducing the power consumption...
Hello,
I'm new to the nRF5340 for BT/BLE; and was looking through older DevZone posts to see if I could find an answer to my question. Specifically, in RE: Query - Nordic...
When playing around with the nrf5340 Audio demo using nrf5340 Audio eval kits, if you play a tone through USB and transmit that through the Gateway to the Headset, you can...
