Hi all,
I am working on a project that requires me to run the SHAKE128 and SHAKE256 algorithms as specified in FIPS 203. I am wondering if it is possible to implement these...
Environment
SoC: nRF54LM20A (cpuapp, non-secure / TF-M)
nRF Connect SDK: v3.3.0
sQSPI soft peripheral driving an AMOLED display via the FLPR
BLE active via MPSL...
Hi,
We had connectivity issues on our end for the Message Routing Service webhook since May 13, 2026. It has been restored and tested with the nRF Cloud verification test...
Hi,
I see the different behavior of the function sd_ble_gap_conn_param_update when connected to Windows integrated Bluetooth.
Using bare-metal SDK v0.9.0 it succeeds...
Hello Team,
We are evaluating an architecture where an NXP MIMXRT700 EVK powers an nRF9151 DK externally while using the nRF9151 DK as an LTE modem.
Hardware:
MIMXRT700...
Hello, We have registered our project with Nordic. Our project ID is 60803622472. Project title: DECT NR+ Star Topology Sensor Node Evaluation with nRF9151 We would like to...
Hi all. I am testing the NPM1300 with nrf54l15 using vallina Zephyr. I've setup device tree for npm1300 to generate interrupt on its GPIO0 when there is event.
When Vbus...
Hi,
I'm using the NRF52811.
In my schematic, the SWDCLK and SWDIO is connected to an external connector and the NRF52811 is connected to MCU through the SPI channel...
Hello
I'm having problem with UDP reception. I'm using nrf9160 with modem firmware 1.2.3, nRF Connect SDK v1.4.0, LTE-M.
I can receive UDP packets in the device as long...
Hi I am designing an intercom and I need help related to it. The following are the requirements of my project. I need an intercom module through which two-person can communicate...
Hi
Now I have a PCA10040 board and MDBT42Q board. I intend to transfer data between two boards via ESB TX and ESB RX example. However, with MDBT42Q I used nRFgo Studio to...
Hi,
We would trigger button to send zdo_mgmt_leave_req to coordinator for leaving the group.
When coordinator is not on power up, we would receive the 0xFF at callback...
Hi,
I want to calculate throughput rate using data that nRF52840 dongle working as sniffer captured.
Wireshark shows 'time' , 'delta time' and 'packet time'.
I think...
Hi,
I have serval questions about TX power settings.I wan to increase power to +8dBm,but the result is no effect.
1 Before reseting Tx power,call nrf_802154_tx_power_get...
Hi There,
Custom xamarin bluetooth app [using Plugin.BLE] is failing to connect to the device using ConnectToKnownDeviceAsync approach. User uses tap-to-pair and tries to...
Hi ,
We have a requirement to use the end device. The device should be an sleepy end device normal . When we want to transmit a large data to router , we want make this...
Hi Sir:
I am using SDK nRF5_SDK_17.0.2,the chip is nRF52810. Using the ble_peripheral\ble_app_uart.
The IO is using P0.6 as the BLE Uart's RX Pin,And P0.7 is used as BLE...
Hello, I was successful in using Arduino headers/ libraries to program my nRF52 DK, but now I am attempting to recreate the project in Segger V5.34 for MacOS for potential...
I want to use 52840dk to implement a file system to save some data. I am using NCS V1.4.99. I tried two samples , v1.4.99-dev\zephyr\samples\subsys\fs\littlefs and v1.4.99...
Hello,
I have just purchased a nRF9160 development kit and created a new account on the nRF Cloud website. I was following along with the getting started video for the development...
I have configure a authorized read from a service's characteristic as below .
void ble_band_ble_evt(ble_evt_t const * p_ble_evt, void * p_context) { ble_band_t * p_band...
