Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I have a product which uses the nRF52840 SoC that will also have NFC functionality. The housing of the PCB is sort of forcing a custom design for the NFC Antenna.
We need...
Hi All,
I am using Segger ISP1430603E board to program my nRF development kit. ( ISP1507AX )
With SES I am able program, debug the application.
I would like to program...
Hi there,
I am wanting to develop a custom PCB for the nRF52833 SoC. I am basing it off the nRF52833 DK! As such, most of the schematic labels are identical.
For our custom...
Hi,
When I do a secure DFU (screen dumps pasted ), it failed with error code 0x8005. It worked on WIndows 7 PC.
//==================Linux System Report
# nRFConnect...
where is UARTE configuration in sdk_config.h? According to this doc (for SDK15.3/UART):
infocenter.nordicsemi.com/index.jsp It seems I can follow the steps to enable UARTE...
Hi,
I am using 2 PCA10040 kits provisioned in the same group. I want to change the payload on button press event from client side which I can receive on server side. How...
I have a nordic kit but the dongle or the kit is not recognized by the computer. Is there a driver that needs to be installed before this will happen? I've already installed...
Hello Guys,,
I am trying to migrate my project form keil to segger embedded studio. My product is based on sdk 12.2.0, using softdevice s130 on nrf51822. I searched for...
Hi,
we have two nrf52840 which shall connect very quickly.
The scan+advertise cycle is very fast (we have no bootloader). After switching on the peripheral it is recognized...
Hi,
I run into issues working with ads1220. Its behaviour is really strange. When I test it, data output with continuous measurement is 0. In few cases, when I swap din...
I have an nRF52840 dongle that I am using to connect and read/write to a client unit. I have been able to use the nRF Connect Bluetooth Low Energy program to control the dongle...
Hi,
My product continues adv mode after connected with mobile until the amount of connection is full. By the way, there are 4 connect handle in my product.
My client use...
