Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hello. I am trying to connect nRF 52840-DK and LTC 5800-WHM with UART. The communication conditions are as follows. Baud rate: 115200 Data: 8 bits Stop bit: 1 bit Parity:...
Hello Community,
I am trying to use Black Magic Probe, an open-source ARM GDB debugger to develop an embedded ARM application using an nRF52832. Here are the parts that...
I am trying to configure two ports as outputs, setting them to Vdd and toggling them. The two ports in question are Po.06 and Po.07.
Here is my code to configure these ports...
Hi,
I didn't understand the function of softdevice. I have a custom nrf52832 board. My requirements;
-2 uart,2spi,1i2c
-OTA update
Should i use a softdevice in nrf...
I have been playing around with example projects in SES (I'm using SDK 15.2.0, SES version 3.52a).
Now wish to start a project from scratch, and import libraries from the...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
We work with custom firmware and use the softdevice 2.0.1 on the nrf51822
I upload the firmware as .zip file using the android nrf Toolbox, which works fine, but when performing...
hi there,
i have made the application and dfu working but there is a smal issue. if i program dfu and application from nrfgo studios the dfu run continuously and app does...
Hi, I'm trying to use the light_switch example in the Mesh SDK 2.1.1 to build a small experiment to count how many messages are received by the server when sending a consecutive...
Hello,
I am trying to do USB DFU on (NRF52840 with SDK 15.2) but when i run the nrfutil command it gives an error:
command: nrfutil dfu usb_serial -pkg ble_hrs_combo...
I've setup, compiled and run the BLE Beacon project an have made some changes. Now I need to enable the UART. Simply adding UART files to the project does not work due to...
Hi
We've developed a wearable device and are changing from a rigid PCB to a full flex PCB. I want to know what adjustments is needed for RF output because of this change...
I am running an example from Mesh SDK (v2.1.1) named "ble_app_uart_coesixt". I see device in Bluetooth list, everything is ok. But I need to provision this device using my...
Hi,
I am using a Sparkfun nRF52832 dev board and SES with the Jlink mini to program it.Our project involved the ability to use the micro as a keyboard so I am playing with...
I am working with NRF52832 and S132. I have successfully captured signals with the ADC (with RTC events at a frequency of 500Hz) and synchronized them using this beacon/scanner...
