Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I'm playing with two thingy and I'm trying to make a sort of walkie talkie with them.
I wrote the code for the sound service client, then modified other parts...
Hi,
i have downloaded latest SDK Version 15.0.0 when i try to run any examples i finding this error
Error #544: Required Software Pack 'NordicSemiconductor.nRF_DeviceFamilyPack...
Hi Team,
There are many ways to implement PWM in nRF52.
Can someone help me understand which is the most power-optimized way along with the softdevice? Using PWM peripheral...
After disconnecting from chip I can not connect it with the same phone .And the chip will restart when we try to reconnet with the same phone (the phone have been deleted...
Dear friend,
The user experience of PPK desktop application is terrible. There is no guider about using this application in the PPK user guider 2.0. I got some problems...
Hi,
we are using the PPK for a while (Software version 1.0.0). For some reason the calibrated values haved changed and very high current values are showing up. I've recalibrated...
Hi Team,
S132 V5.0 for nRF52832 can support up to 20 links.
If the connected links have different ATT MTU setting, what is the behavior of the device/softdevice regarding...
Hi,
I am using nRF52832 SDK 14.2.0 and i added the header file in project path "nrf_dfu_svci.h" but still i getting the error ..\..\..\..\..\..\components\libraries\bootloader...
Hi all,
I am using segger studio , i am trying to run examples of mesh alpha sdk that nordic provides. I can able to dump the code on board successfully. But if i try to...
I am using the nrf_i2s driver, and it works properly ... with CONFIG.CHANNELS set to stereo.
But for my application, I only need to drive data onto SDOUT left channel. ...
Dear sir please help..its urgent.
i am using below configurations. Nordic - nRF52832-QFAA-B Soft device - 132 SDK - nRF5_SDK_14.2
I am following the "ble_app_att_mtu_throughput...
Hi all,
I am using the nRF51822 BLE with custom board, I want to configure Timer1 to generate IRQ for every 1ms and Timer2 to generate IRQ for every 1us. I want to run...
Hi,
I want to change the UART0 baud rate at runtime (the peripheral has switched to a new rate). Is it enough to reset to (say) 9600 baud, like:
NRF_UART0->BAUDRATE =...
Hello,
I am using the nRF52840 DK with Keil to develop. I have a structure defined as follows:
I have verified that uint8 is 1 byte, uint16 is 2 bytes, and uint32 is...
